Wattstopper
®
Passive Infrared Wall Switch Occupancy Sensor (version 3)
Détecteur de présence interrupteur mural infrarouge passif (v3)
Sensor de ocupación con interruptor a la pared y tecnología de
infrarrojo pasivo (v3)
Installation Instructions • Instructions d’Installation • Instrucciones de Instalación
No: 23950 – 10/18 rev. 3
Catalog Numbers • Les Numéros de Catalogue • Números de Catálogo: PW-100/PW-100-347/PW-200/PW-200-347
Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China
DESCRIPTION AND OPERATION
The PW Passive Infrared Wall Switch sensors use advanced passive infrared (PIR) technology.
The PW sensor can turn a load on, and hold it on as long as the sensor detects occupancy. After no movement is detected for the
selected time delay, the lights switch off. A “walk-through” mode can turn lights off after only 3 minutes, if no activity is detected after 30
seconds following an occupancy detection.
The PW-100 has one relay and one
ON/OFF
button. The PW-200 contains two relays and two
ON/OFF
buttons to allow control of one
or two loads independently. Pressing a button toggles the state of the corresponding relay.
PW sensors contain a light level sensor. If adequate daylight is present, the sensor holds the load
OFF
until light levels drop, even if the
area is occupied. In the PW-200, light level only affects the load on Relay 2. Users can overrule the hold
OFF
function by pressing the
ON/OFF
button. See Light Level Adjustment.
Turning Load(s) ON (ON Mode)
The relays are programmed independently for either Auto
ON
or Manual
ON
. In either mode, the load can be turned
ON
or
OFF
using
the
ON/OFF
button.
Manual ON
DIP 8
ON
for Relay 1
DIP 9**
ON
for Relay 2
With an
ON
Mode DIP switch in the
ON
position, the occupant must press the
ON/OFF
button to turn
ON
the load. The sensor keeps the load
ON
until no motion is detected for the selected time delay. There is a
30 second re-trigger delay. If occupancy is detected during the delay, the sensor turns the load back
ON
.
After the re-trigger delay elapses the
ON/OFF
button must be pressed to turn
ON
the load.
Auto ON
DIP 8
OFF
for Relay 1
DIP 9**
OFF
for Relay 2
With an
ON
Mode DIP switch in the
OFF
position, the load turns
ON
and OFF automatically based on
occupancy. If the load is turned
OFF
manually, Presentation Mode operation applies. This prevents the
load from turning
ON
automatically after it was deliberately turned
OFF
. Pressing the button to turn lights
ON
returns the sensor to Auto
ON
mode.
** PW-100: Switch 9 is not used. PW-200: Switch 9 default is
ON
to comply with CA Energy Commission Title 24 bi-level switching
requirements.
SPECIFICATIONS
Voltages:
PW-100 & PW-200 .......................................120/277VAC, 50/60Hz
Load Limits for each relay:
@120VAC ...............................0-800W tungsten or ballast, 1/6 HP
@277VAC .............................................................0-1200W ballast
Load Type Compatibility:
Incandescent, fluorescent, magnetic or electronic ballast
Horsepower Rating (each relay) ........................ 1/6 HP @120VAC
Time Delay Adjustment .................................................. 5 to 30 minutes
Walk-Through Mode ................3 minutes if no activity after 30 sec.
Test Mode ...................... 5 sec. for 10 min. with DIP switch setting
PIR Adjustment ................................................ High or Low (DIP switch)
Light Level Adjustment ....................................................... 8fc to 180+fc
Alerts ...........................................................Selectable Audible & Visual
US Patents: 5640113, 6617560
PW-100
PW-200