background image

19

NOVO Technical Handbook - NE41 15013-02 v2.0

Indications

3.1 

Visual indications

3.1.1  Front LEDs

In normal operation the front LEDs (L1 – L3) are off. When an error occurs, the 

corresponding LED will indicate the error. The significance of the LEDs is described 

on the bottom label of the unit.
When the unit is running on accumulator power the LED indications will switch to 

blinking to consume less power. See the tables below for all supported indications.
Note that the individual visual error indications can be disabled by configuration. 

Furthermore, all visual error indications can be disabled with a specific configuration 

parameter.

LED indications for NOVO IP/Mobile, NOVO PSTN/GSM and NOVO PSTN+.

L1 (Network)

L2 (AC)

L3 (Accumulator)

Normal mode, no failures

Off

Off

Off

Network failure (IP/Mobile/LINE) On

Off

Off

AC failure

Off

0.5s On/4.5s Off

Off

Accumulator failure

Off

Off

On

Network and AC failure

0.5s On/4.5s Off

0.5s On/4.5s Off

Off

Network and accumulator failure On

Off

On

AC and accumulator failure

Off

0.5s On/4.5s Off

0.5s On/4.5s Off

Network, AC and accumulator 

failure

0.5s On/4.5s Off

0.5s On/4.5s Off

0.5s On/4.5s Off

Radio interference

0.5s On/0.5s Off

0.5s On/0.5s Off

0.5s On/0.5s Off

SIM card failure

0.5s On/0.5s Off

Off

Off

AC and SIM card failure

0.5s On/4.5s Off

0.5s On/4.5s Off

Off

Table 8. 

Front LED (L1 - L3 ) indications.

Firmware download and upgrade indication NOVO IP/Mobile, NOVO PSTN/GSM and 

NOVO PSTN+

When downloading over ftp the sender can set whether the NOVO unit shall indicate 

an ongoing firmware download by blinking the Reset button LED (L5) 0.5s On/0.5s Off 

or not.
There is 

NO

 indication when downloading over USB.

When firmware download is complete the unit automatically reboots and starts the 

firmware upgrade process. During firmware upgrade LEDs L1, L2 and L3 flash in 

synchronization 100ms On/100ms Off and after upgrade the unit starts up normally.

Summary of Contents for NEAT NOVO













































Reviews: