manualshive.com logo in svg

LEGRAND KEOR S 10KVA 1, Operating & Installation Manual

Share
Download
LEGRAND KEOR S 10KVA 1 Operating & Installation Manual Download Page 20

20

The installation and adjustment of distribution panel should be done by 

specialized technician.

The installation and adjustment of distribution panel should be done by 

specialized technician.

Please add double-pole miniature circuit breaker (equivalent UPS input breaker) to distribution board 

where UPS is to be connected. Do not connect any other load to this circuit breaker and please do not 

forget to add leakage current relay.
Connect the phase cable to input 

“L” 

terminal, the neutral to input

 “N”

 terminal.

According to EN 62040-1, the user should place a warning label on the input distribution panel 

and the other primary power isolators, in order to prevent the risk of voltage backfeed. 
This label is sent with the Installation Manual. It indicates:

RISK OF VOLTAGE BACKFEED

• Isolate Uninterruptable Power Supply before working on this circuit.
• Then check for Hazardous Voltage between all terminals including the protective earth (PE).

5.3.1.2. 

Input Connection

Summary of Contents for KEOR S 10KVA 1


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands