LEGRAND Finelite HP-4 Installation Instructions Manual Download

Page: 8 / 9

HP-4 Wet Location Surface Mount Installation Instructions

8 of 9

TE: 09/09/19

Yoke Bracket w/ Screw

#10-32 x 5/8" (provided)

¹ Screwdriver with 6" bit required.

Step 6 - Securing Luminaire Joints

B. Make Electrical Connections

•

Connect plug-together wiring.

Joiner/Ender

Starter

Plug-Together Wiring

A. Secure Joint with Yoke Brackets

•

Before installing yoke brackets, ensure the joining ends of luminaires meet flush and square.

•

CRITICAL: Ensure yoke brackets properly engage with aligner sleeves.

•

Secure joint by threading (but not yet tightening) yoke screws through yoke brackets and

into the aligner sleeves.

•

Tighten yoke screws¹ until joint seam of luminaires is closed.

Joiner/Ender

Cross Section

View

Starter

Yoke Screw

(provided)

Yoke Bracket

(provided)

tooltip

IN ALIGNMENT

CORRECTLY INSTALLED

Luminaire Joint

Joiner/Ender

Aligner Sleeve

Simple

Plug-Together

Wiring

Summary of Contents for Finelite HP-4










Search results

Summary of Contents for Finelite HP-4

Reviews:

Related manuals for Finelite HP-4

Brands by name

Popular brands

LEGRAND Finelite HP-4, Installation Instructions Manual

Search results

Summary of Contents for Finelite HP-4

Reviews:

Related manuals for Finelite HP-4

Brands by name

Popular brands