LEGRAND Finelite HP-4 Installation Instructions Manual Download Page 5

Page: 5 / 9

HP-4 Wet Location Surface Mount Installation Instructions

5 of 9

TE: 09/09/19

CONTINUED

Step 4 - Mounting Starter to Structure

A. Make Electrical Connections

Sealing O-Ring

(provided)

Wire-nut electrical

connections.

WIRING LEGEND

Black

Hot

Line Voltage

White

Neutral Line Voltage

Green

Ground

Grey

Dimming

0-10V DC

Purple

Dimming

0-10V DC

•

Install conduit, sealing o-ring, and nylon nut onto the luminaire.

•

Wire-nut electrical connections. See wiring legend above.

Flex Conduit

(by others)

Nylon Nut

(provided)

Ceiling

Nylon Nut

(provided)

•

CRITICAL: If luminaire contains a sensor, refer to Sensor Addendum before mounting starter to structure.

•

While properly supporting luminaire, maneuver luminaire near wall/ceiling.

•

Make electrical connections at TOP of luminaire.

Sealing O-Ring

(provided)

Starter

Nylon Nut

(provided)

Sealing O-Ring

(provided)

0-10V

Dimming

Summary of Contents for Finelite HP-4










Search results

Summary of Contents for Finelite HP-4

Reviews:

Related manuals for Finelite HP-4

Brands by name

Popular brands

LEGRAND Finelite HP-4, Installation Instructions Manual

Search results

Summary of Contents for Finelite HP-4

Reviews:

Related manuals for Finelite HP-4

Brands by name

Popular brands