background image

 LPE1U

Installation Instructions

14

18. Make sure latching flags are in "closed" position prior to 

using cart! (See Figure 20)

IMPORTANT ! : 

Manufacturer recommends using cable 

ties (K) to secure the latching flags in closed position on 
both sides if padlock is not being used. (See Figure 20)

Figure 20

Adjustments

Height Adjustment

1.

Press "UP" or "DOWN" buttons to raise or lower height as 

desired. (See Figure 21)

Figure 21

Save Height Levels

1.

Adjust height until desired preset level is reached using 

"UP" and "DOWN" buttons. (See Figure 21) 

2.

Press "SAVE" button. (See Figure 21)

3.

Press one of three preset buttons (., .. or ...) to save preset 

position. (See Figure 21)

4.

Repeat Steps 1-3 as desired.

Tilt Adjustment

IMPORTANT ! : 

Remove display from mount prior to 

adjusting tilt!

5.

Use 3/16" hex key (H) to remove tilt adjustment screw. (See 

Figure 22)

6.

Adjust faceplate tilt and re-install removed screw in either 

the middle hole for 2° tilt or the lowest hole for 4° tilt. (See 

Figure 22)

Figure 22

Roll Adjustment

7.

Loosen nuts on back of faceplate. (See Figure 23)

8.

Adjust roll as desired. (See Figure 23)

9.

Tighten nuts on back of faceplate. (See Figure 23)

Figure 23

(K) x 2

"UP"

"DOWN"

"PRESETS" "SAVE"

5

6

6

remove

re-install

(rear view)

8

7

9

Summary of Contents for CHIEF LPE1U

















Reviews: