manualshive.com logo in svg

LEGRAND CHIEF 25-PTS-2000 Series, Installation Instructions Manual

Share
Download
LEGRAND CHIEF 25-PTS-2000 Series Installation Instructions Manual Download Page 8

Installation Instructions

PTS

7

MOUNT THE DISPLAY

1.Follow the instructions for installing the 25-PSB bracket(s) for 

your specific flat panel display.

WARNING:  Watch for pinch points. Do not put your fingers 

between movable parts.

2.

Before lifting your flat panel display, make sure the latch of the 
PTS is lowered and will not interfere with mounting the display 
(see Figure 6).

3.

Using two people, align the Q-latch buttons with the Q-latch 
openings and install the display. Make sure the buttons of the 
Q-latch bracket fully engage all the Q-latch openings on the 
PTS (see Figure 7).

4.Secure the display to the 25-PTS by completely engaging the latch 

(see Figure 8).

5.

Connect and secure power/audio/video cables.

REMOVE THE DISPLAY

1.

Disconnect power/audio/video cables.

2.

Disengage (lower) the  latch.

3.Using two people, lift the display from the 25-PTS.

Summary of Contents for CHIEF 25-PTS-2000 Series









Reviews:

No comments

Brands by name

Popular brands

Load more brands