Led Lenser H14.2, Operating Instructions Manual

Page: 4 / 34

function). A short flash indicates the darkest (5
lumens) or brightest setting.
In the Pulse - function, you can speed up or
slow down the flashing frequency by turning the
multi-function "Wheel" switch ( Pulse function).
d) Boost Mode: in any state, push the front
switch for 2 seconds to achieve boost mode.
After 10 seconds the flashlight will return to the
previous setting.
The Light Functions above are in a loop.
Note that when switching modes, press the
“Multi-function Wheel” switch on the back for no
longer than 2 seconds, otherwise the product
will turn off.
6. Energy Modes
By selecting one of the two Energy Modes
(Energy Saving or Constant Current), you take
a decision on how the energy contained in the
accumulator respectively in the batteries is
used.
6.1 Energy Saving:
The light output is controlled
by the integrated Smart Light Technology (SLT).
The brightness is matched to the real conditions
that occur during normal use of the lamp, thus
providing a longer burn time.
6.2 Constant Current: This Energy Mode allows
the continuous use of all the Light Functions
with a more or less constant light output. This
Energy Mode is to be preferred when a high
brightness level is more important than a long
burn time.
Changing of the Energy Modes
For changing the Energy Modes, only can be
active when the flashlight in the Light Program
White. Keep the LED off, and then switch the
“Multi-function Wheel” switch on the back for 8
times and keep it pressed for approx. 2 seconds.
Then you change the mode between „energy
mode“ and „constant current mode“.
a) Constant current mode: In case the
brightness reduces immediately in 2 seconds,
the H14.2 is on constant current mode;
b) Energy saving mode: in case the brightness
reduce gradually to zero, the H14.2 is in the
Energy Mode.
With this procedure, you can switch between
the two Energy Modes. It is not possible to
determine in which Energy Mode the H14.2
is. To find this out, you must carry out the
procedure. If the H14.2 is thereafter not in the
desired Energy Mode any more, you must repeat
the procedure again. The flashlight will reset to
energy saving mode if you change the battery or
cut the power.
7. „Transport Lock“
When the H14.2 is off, push the front switch
for approx. 5 seconds till the light turns off
in order to enable the “Transport Lock.” The
H714.2 therefore cannot be switched on; either
intentionally or unintentionally and inadvertently
consume energy.
To deactivate the “Transport Lock”, just press
the front switch again for 5 seconds. The
headlamp will now return to the Light Program.
8. Reset function
If the alkaline batteries are taken out the battery
box you have "reset" the H7. You have thus reset
a few functions so that the “Transport Lock” (see
Section 6) is deactivated and the Light Function
Dim (see Section 5.1) is set to low brightness.
9. Changing of the Alkaline batteries
Prior to the change, turn off the H14.2.
On the back of the battery back, where the
headband is attached, there is the gate to the
inside of the battery box. Open the battery box
rear cover, remove the battery, and then insert
a new one.
Insert a new one (4 AA alkaline batteries/ 4 AA
Ni-MH rechargeable batteries/ 4 cr123a alkaline
batteries/ 2 ICR18650 Li-ion battery packs can
be used on the product) .
Please notice, do not charge the alkaline battery!
During insertion, it is always necessary that it is
in the correct direction. Therefore, pay attention
to the polarities (+ and -) both on the battery
box and the alkaline batteries. Otherwise, there
is a risk for damage batteries and a possible
explosion.
After replacing the batteries, the cover of the
battery box has to be put back into place.
10. Headband
The headband can be washed by water.
Please refer to the picture to disassemble and
assemble the headband.
11. Batteries
Never use non rechargeable batteries and
accumulators together.
Change always all batteries at the same time.
Use in the H14.2R below batteries can be
used 4xAA alkaline/ 4xAA Ni-MH/ 4Xcr123A
alkaline/ 4xCR123A rechargeable/ 2xICR 18650
batteries/ 2xICR 18650 Li-ion battery pack.
If you intend not to use the item for an extended
period, please take out the batteries in order to
avoid damage.
Used batteries and accumulators have to be
taken out the item and disposed of in keeping
with the national laws.
12. Cleaning
To clean, use a dry, lint-free, clean cloth.
If salt water is spilled on the head lamp, it must
be immediately entirely removed with such a
cloth.
The headband can be washed in a washing
machine at 30 °C.
13. Scope of delivery
The H14.2 headlamp is supplied with the
following accessories:
1 H14.2 headband
4 AA alkaline batteries
1 user manual
14. Caution
Do not swallow any small parts or batteries/
accumulators that are present. The products
or parts thereof (including batteries /
accumulators) must be stored out of the reach
of children.
For safety and approval reasons (CE), the
product must not be modified and/or changed.
The product is to be used exclusively as an
03
LED LENSER® * H14
.2