manualshive.com logo in svg

Lectric XP Lite, Owner'S Manual, Page: 40 / 55

Share
Download
Lectric XP Lite Owner'S Manual Download Page 40

LECTRICEBIKES.COM | 602.715.0907

40

•  Do not expose the charger to rain or wet conditions. If water 

enters a charger, there is a risk of electric shock.

•  Only use the original Lectric eBikes battery charger supplied 

with your eBike or one approved for your eBike by the 

manufacturer and purchased from a trusted source. Bypassing 

the battery charger or the use of a non-approved or counterfeit 

battery charger can lead to death or serious injury.

•  Keep battery charger clean. Contamination can lead to the risk 

of an electric shock. Clean only with the use of a damp cloth 

(mild soap/water).

•  Always check the charger, cable, and plug before use. Stop 

using the charger if you discover any damage. Do not open the 

charger. Damaged chargers, cables, and plugs increase the risk 

of electric shock.

•  Do not operate the charger on an easily ignited surface (e.g. 

paper, textiles, etc.) or in a flammable environment. There is a 

risk of fire due to the charger heating up during operation.

•  Take care if you touch the charger while it is charging. 

The charger can get very hot, especially when the ambient 

temperature is high.

•  The battery may give off fumes if it becomes damaged or is 

used incorrectly. Ensure the area is well ventilated and seek 

medical attention should you experience any adverse effects. 

These fumes may irritate the respiratory tract.

•  Batteries must not be subjected to mechanical shock. There is a 

risk of damage to the battery pack.

•  Keep the battery charger away from children. This will ensure 

that children do not play with the charger.

•  Persons who are not capable of safely operating the charger 

because of their physical, sensory, or mental limitations, or 

because of their lack of experience or knowledge, may only use 

this charger under supervision or after having been instructed 

by a responsible person. Otherwise, there is a risk of operating 

errors and injuries.

•  Note the household voltage! The voltage of the power supply 

must correspond to the specifications given on the battery 

charger nameplate.

Summary of Contents for XP Lite
























































Reviews:

No comments