manualshive.com logo in svg

Lectric XP Lite, Owner'S Manual, Page: 36 / 55

Share
Download
Lectric XP Lite Owner'S Manual Download Page 36

LECTRICEBIKES.COM | 602.715.0907

36

BATTERY PACK

The term

 battery pack

 refers to all original Lectric eBikes  

battery packs.
The safety of both our customers and our products is important 

to us. Our eBike batteries are lithium ion batteries, which have 

been developed and manufactured in accordance with the latest 

technology. We comply with or exceed the requirements of all 

relevant safety standards. When charged, these lithium ion batteries 

contain a high level of energy. If a fault occurs (which may not 

be detectable from the outside), in very rare cases and under 

unfavorable conditions, lithium ion batteries can catch fire.
Take care when using and charging your battery. Failure to follow the 

guidelines below could result in damage to property and/or serious 

injury. Contact Lectric eBikes immediately if you have any questions 

regarding battery safety.
Your Lectric eBike battery must not be opened, even for repairs. 

There is a risk your eBike battery could catch fire, e.g. due to a short 

circuit. This risk increases if an eBike battery which has already been 

opened is reused at a later point in time. Do not attempt to repair an 

eBike battery in the event of a fault. Have it replaced with an original 

Lectric eBike battery pack.
The battery is protected against deep discharge, overloading, 
overheating, and short-circuiting by Electronic Cell Protection (ECP). 
In the event of a fault, a protective circuit switches the battery pack 
off automatically.

Only use original Lectric eBike batteries for your eBike. Using other 

batteries can lead to injuries and pose a fire hazard. Lectric eBikes 

accepts no liability or warranty claims if other batteries are used.
To prevent serious injury or death:
•  Do not leave your battery unattended while charging.
•  When removing the battery, unplug the rubber stopper on the          

charging point.

Battery Safety

WARNING!

Summary of Contents for XP Lite
























































Reviews:

No comments