background image

10

The Lectra/San EC Type I MSD can be connected to
two marine toilets.  However, the two toilets must be
in close proximity to:

1. Reduce the pressure requirement to move waste

through the connecting hose.

2. To decrease the possibility of untreated sewage

remaining in the lines.

The Lectra/San EC Treatment Tank should be lo-
cated midway between the two toilets.  The maxi-
mum distance from either toilet to the tank should
not exceed six feet.

A kit is available for field conversion to dual toilet
operation:

Lectra/San EC Dual Control Component part
#LSTEDC (for 12 V units):

1. Control Indicator Panel with ribbon cable at-

tached.

2. Salt Feed Tank complete.

INSTALLATION

1. Adding second toilet - Install Lectra/San and

first toilet per manual, then add second toilet by
connecting discharge line to the opposite side of
the tank.  Remove the plug to allow connections.
(See Figures #11A and #11B)

2. Electric toilet - Installations with two electric

toilets must be wired to work independent from
the Control Indicator Panels.  Contact Raritan
Customer Service for instructions.

3. Mounting - Each toilet should be installed within

six feet of Lectra/San EC.

4. Control Indicator Panel - The Dual Control

Indicator Panel attaches directly to the Lectra/
San EC circuit board, the original Control Indica-
tor Panel connects inline using the special con-
nector attached to the dual control ribbon (See
Fig. #12A).

OPERATION

Indicator/LED lights will indicate operation on both
panels when any toilet is in use.  DO NOT activate
"Push to Flush" button if another toilet is in use.

A Salt Feed Tank should be installed in each toilet's
intake hose if operating in fresh or brackish water.
The flow control for each Salt Feed Tank must be set
independently.

USING THE LECTRA/SAN EC SYSTEM WITH TWO MARINE HEADS

NOTE:  Single push button operation of LST/EC or toilet cannot be installed in this application.

FIG. #11A  Lectra/San EC Mounted Below the Waterline

FIG. #11B  Lectra/San EC Mounted Above the Waterline

Control #1

Control #2

Ribbon
Cable

Ribbon
Cable

FIG. #12A

Dual  Control  Cable (#31-406)

Circuit Breaker

Battery

Lectra/San

Treatment

 Unit

less than 6'

<

less than 6'

>

<

>

Summary of Contents for EC













Reviews: