LeCroy USB Protocol Suite Advisor T3 User Manual Download Page 295

Page: 295 / 388

USB Protocol Suite

User Manual

Chapter 11: Traffic Generation (2.0)

LeCroy Corporation

281

11.1.2 Connecting to Voyager

The connections differ for Host Emulation and Device Emulation.

Full Speed, Low Speed, and Hi Speed connections are the same.

11.1.2.1 Hi/Full/Low Speed Host Emulation

For Host Emulation Hi, Full, or Low Speed, connect to the Voyager according to the
following diagram.

Summary of Contents for USB Protocol Suite Advisor T3





































































































































































































































































































































































































Search results

Summary of Contents for USB Protocol Suite Advisor T3

Reviews:

Brands by name

Popular brands

LeCroy USB Protocol Suite Advisor T3, User Manual

Search results

Summary of Contents for USB Protocol Suite Advisor T3

Reviews:

Brands by name

Popular brands