manualshive.com logo in svg

LeCroy USB Protocol Suite Advisor T3, User Manual

Share
Download
LeCroy USB Protocol Suite Advisor T3 User Manual Download Page 129

USB Protocol Suite

 

User Manual

Chapter 5: Reading a Trace

LeCroy Corporation

 115

5.34 Decoding Protocol-Specific Fields in 

Transactions and Transfers

When transfers or transactions are displayed, the fields in setup transactions and in 
control, interrupt, and Bulk transfers do not get decoded (by default) and are shown in 
hexadecimal values. The exceptions are setup transactions and control transfers for 
standard USB device requests, which are always decoded.

To show specific decoding for class- and vendor-specific device requests and endpoints, 
you have to use the decoding association mechanism that is described in Chapter 9 on 
decoding. When you have performed the association, you see the protocol-specific fields 
of transfers and transactions decoded in the trace view.

5.35 Switch to Host Wire Adapter Segment View

A 

Host Wire Adapter Segment

 is one or more transfers between a PC and a host wire 

adapter. To view host wire adapter segments, switch to the Host Wire Adapter Segment 
trace viewing level.

To select the Host Wire Adapter Segment trace viewing level: 

•

Click

on the toolbar.

OR

•

Select 

View > HWA Segment Level

.

OR

•

Select

 Setup > Display Options

 to display the

 

Display Options window, check 

HWA Segment

, and then click 

OK.

Summary of Contents for USB Protocol Suite Advisor T3





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands