manualshive.com logo in svg

LeCroy USB Protocol Suite Advisor T3, User Manual

Share
Download
LeCroy USB Protocol Suite Advisor T3 User Manual Download Page 282

Chapter 10: Recording Options

USB Protocol Suite User Manual

268

LeCroy Corporation

•

Timer

•

SCSI

•

Primary Command Set

•

Block Command Set

•

Media Changer Command Set

•

Stream Command Set

•

Multi-Media Commands

•

Controller Commands

•

Enclosure Services

Event Properties

The Event Properties dialog lists the Properties and their Values (see “Events and Event 
Properties for USB 2.0” on page 256).

Note: 

The Header Pattern tab is different for the USB 3.0 recording rules. 

Most fields are mask and match. The Type and Subtype fields have drop-down menus. 
You can set the Subtype to: 

•

Reserved

•

Set Link Func

•

U2 Inact Tmt

•

Vndr Development Test

•

Port Capability

•

Port Config

•

Port Cfg Ack

Summary of Contents for USB Protocol Suite Advisor T3





































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands