manualshive.com logo in svg

Leadshine ES-DH1208, Hardware Installation Manual, Page: 24 / 27

Share
Download
Leadshine ES-DH1208 Hardware Installation Manual Download Page 24

   

Hardware

 

installation manual of the ES-DH series drives

 

20 

Over-current Protection 

Over-current  protection  will  be  activated  when  continuous  current  exceeds  the  limit  or  in  case  of 
short circuit between motor coils or between motor coil and ground, and RED LED will  blink once 
within each periodic time. 

Over-voltage Protection 

When power supply voltage exceeds the limits,  protection will be activated and  red LED will blink 
twice within each periodic time. 

!

Caution

When above protections are active, the motor shaft will be free or the LED will 
blink. Reset the drive by repowering it to make it function properly after removing 
above problems. Since there is no protection against power leads (

﹢

,

﹣

) reversal, 

it  is  critical  to  make  sure  that  power  supply  leads  correctly  connected  to  drive. 
Otherwise, the drive will be damaged instantly.   

Position Following Error Protection 

When  the  position  error  exceeds  the  limit  (software  configurable,  see  software  manual),  position, 
protection will be activated and red LED will blink seven times within each periodic time. 

www.servosystem.ru    +7(495) 407-01-02

Summary of Contents for ES-DH1208




























Reviews:

No comments