manualshive.com logo in svg

Leadshine ES-DH1208, Hardware Installation Manual, Page: 11 / 27

Share
Download
Leadshine ES-DH1208 Hardware Installation Manual Download Page 11

   

Hardware

 

installation manual of the ES-DH series drives

 

7 

Connecting PC 

A  built-in  RS232  communication  port  in  the  easy  servo  drive  is  used  for  communication  and 
configuration. Connect this port to the PC

’

s serial port. Then you can turn the motor in PC software. 

This software - ProTuner, is designed to configure the easy servo drive. You can define the control 
mode, microstep resolution, current rate, active level of inputs/outputs in ProTuner.  

The ProTuner can be downloaded from our website: 

http://www.

servosystem.ru

 or you may also get 

it from our CD. It is recommended to get it from the website because it is always the latest. Install it 
in your PC and make it ready for use later. 

Connect ES-DH drive to PC 

A RS232 cable is needed for the communication between the drive

’

s RS232 port and the PC

’

s serial 

port. It will be shipped with the kit if you include it in the order. It is also possible to make this cable 
by yourself. One end of this cable is a RJ-11 header and the other end of cable is a 9 pin D-Sub female 
connector. If your PC does not have a serial port, a USB-to-Serial converter which simulates the serial 
port is required.

 Note that the power should be turned off when you perform any connections!

 

When  you  open  ProTuner,  a 

“

Connect  to  drive

”

  window  appears.  The 

“

Baud  Rate

”

  and 

“

Device 

Address

”

 are fixed. You only need to select the 

“

Com Port

”

 regarding to the actual serial port or the 

mapping port of a USB-232 converter. Check the 

Device Manager

 for the mapping port number of 

the USB-232 converter.   

Or 

RS232 Cable 

USB-232 Converter 

ProTuner 

www.servosystem.ru    +7(495) 407-01-02

Summary of Contents for ES-DH1208




























Reviews:

No comments