background image

17

6. Service and Maintenance

6.3 Care and Maintenance

To ensure perfect performance of the TINY-FOGGER, you should consider the

following notes:

• Make sure the fluid bottle as well as of the connecting spout and the quick

connector are clean and free from small bits of dirt.

• Clean the unit from time to time, especially if you use it in a built-in state/

condition. Unscrew the unit with a suitable screwdriver (No. 1 Phillips) and
wipe it out carefully using a dry, fluff-free cloth.

• Should the vaporizer become clogged, please change it in the way as described

in section 6.3.

• If the TINY-FOGGER isn‘t in use for a longer time, please take care that the

fluid tube is emptied. It could be that some fluid drops come out of the nozzle
and the surrounding gets wet and greasy.

• the battery is discharged => disconnect the machine from the battery and charge

the battery

• the vaporizer is clogged or broken  => change the vaporizer (see point 6.1)

Note: the new vaporizer must be calibrated as explained in point 6.1.3!

6.2.2 The yellow LED lights permanently if…

• Disconnect the machine from the battery

• Remove the new vaporizer as explained in point 6.1.1

• Connect the machine to the battery and press the blue button [11] at the back

of the machine once

• Disconnect the machine from the battery

• Install the new vaporizer again and calibrate it as explained in point 6.1.3

6.2.3 If the new vaporizer can‘t be calibrated (no confirmation of the process by

the LED), please perform the following procedure:

Summary of Contents for TINY-FOGGER



















Reviews: