background image

Technical specifications

Actuators

Descriptions

8310-2420 Series

Input voltage 

(for LED electronic board)

24V DC

Current draw 

(for LED electronic board)

110 mA @ 24 VDC

Contact rating

3A @ 30 VDC

Lumina red

14.8 lumens, 1600 mW

Lumina green

3.8 lumens, 330 mW

Sounder

3200 ± 300 Hz @ 85 dB

Relay contact

1 x Form C

Mounting

4 x #12 wood screws with anchors

Construction

Flame-resistant black ABS (insert-translucent ABS)

Finish

Attractive pebble finish

Dimensions

6 1/2” x 6 1/2” x 2” (165 mm x 165 mm x 51 mm)

E-strike

Descriptions

8310-2420 Series

Voltage

24 DC

Current Draw

150 mA maximum @ 24 VDC

Static strength

1000 lbs.

Dynamic strength

50-ft. lbs.

Mode

Field selectables

Fail safe/fail secure

Mechanical adjustment

Strike body/faceplate

Operation

DC-silent

Duty

Continuous

Dimensions (body)

3 3/8” x 1 7/8” x 1 7/32” (86 mm  x 47 mm x 31 mm)

Transformer

Descriptions

8310-2420 Series

Input voltage

120V AC

Output voltage

24V AC @ 60 Hz

Class

B2

Power

50 VA

DPS Switch

Descriptions

8310-2420 Series

Power max.

3.0 W

Electrical configuration

SPDT

Suggested Wiring

22AWG

Gap distance max.

0.75”

Operation at a glance

When the exterior PUSH TO OPEN button is pressed it will trigger the PBTN input on its electrical board causing its N.O. 

relay contact to send a momentary closure to the outside PUSH TO OPEN on the restroom kit allowing the door to swing 

open. When the interior PUSH TO LOCK button is pressed, it will trigger the PBTN input on its electrical board, causing its 

N.O. relay contact to send a momentary closure to inside PUSH TO LOCK , causing the restroom kit to lock the restroom 

and switch the electrical board colors from green to red. The inside PUSH TO OPEN button is wired directly to inside PUSH 

TO OPEN on the restroom kit. When pressed, the restroom will unlock and the door will swing open. The restroom can also 

be unlocked by opening the door from the inside, which will break the door contact circuit, causing the restroom kit to reset 

and unlock the door. The electrical board will switch back to green, signaling that the restroom is now vacant.

Summary of Contents for 8310-2420





















Reviews: