LBC LPC-19-G Operator'S Manual Download Page 6

 

   EQUIPMENT DESCRIPTION                                              I  

 

Exterior Dimensions   

See Configurations Section. 

 

Construction 

 

The exterior top, front, rear and sides are constructed of stainless steel, as is the sandwich door and oven interior 
(including all interior ducting, conveyor belt and entrance/exit shelves). 

 

The exterior underside is constructed of corrosion-resistant aluminized steel. 

 

The sandwich door window is constructed of thick, tempered safety glass. 

 

Performance 

 

Fast-acting gas burner is utilized for rapid run-up and recovery. 

 

Rear-mounted fan thoroughly circulates convection air for rapid cooking and even browning of the food product. 

 

The cook chamber is insulated with high-temp insulation for reduced heat loss and increased energy efficiency. 

 

Controls 

 

Simple, intuitive and easy-to-understand layout. 

 

Large displays for time and temperature. 

 

Belt Time Range:  03m:00s – 30m:00s.

 

 

 

Set Point Range:  145-570

o

F. 

 

Temperature scale can be easily set to either 

o

F or 

o

C. 

 

On shutdown, the last settings used are retained in memory and reappear on the subsequent startup. 

 

Features 

 

Cool-Down Feature.  This automatic feature allows the oven to cool slowly to extend the life of the interior electrical 
components.  On shutdown, if the oven cook chamber temperature exceeds 200

o

F, the heater fans continue to run 

for a period after the heaters have turned off.  Once the oven cook chamber temperature has dropped to 200

o

F, the 

fans will automatically stop and the control will turn off. While in cool-down Mode, the word “CooL” will appear in 
the Conveyor Speed display.   

 

 

Change Belt Direction.  The direction of the belt can be changed to run from left to right or right to left.  A two-
position belt-direction switch with identifying label is located at the backside of the cook chamber.  Set the switch 
to your desired direction. 

 
 

 
 
 
 
 
 
 
 
 

Summary of Contents for LPC-19-G

















Reviews: