17
EN
STANDARD FITTINGS
Make sure the following are contained in the purchased product pack:
• high-pressure cleaner;
• high-pressure delivery hose with quick coupling;
• spray gun;
• lance hose;
• suction connection kit;
• external detergent suction hose kit;
• instruction manual - safety precautions;
• instruction manual - operation and maintenance;
• warranty certificate;
• after-sales centre booklet;
• EC declaration of conformity;
• nozzle cleaning pin.
In case of problems, contact your dealer or an authorised after-sales centre.
OPTIONAL ACCESSORIES
The standard fittings of the high-pressure cleaner can be integrated with the following range of accessories:
•
BA
type water mains disconnector: mandatory for connecting up to the drinking water mains.
• sandblasting lance: designed to clean surfaces, eliminating rust, paint, scale, etc.;
• drain cleaning kit: designed to unblock pipes and ducts;
• rotating-nozzle lance: designed to remove resistant dirt;
• foam lance: designed for more effective detergent distribution;
• lances and nozzles of various types.
INSTALLATION - FITTING ACCESSORIES
• Connect the quick coupling (15) of the hose (14) to the water outlet connection (7), screw down and secure.
Operation E in fig. 6.
• Screw up the connection (13) of the high-pressure hose to the thread of the spray gun (9) and tighten well
using two 22 mm fixed wrenches (not supplied).
Operation D in fig. 6.
• Fit the filter (21) in the water inlet connection (20). Fit the seal (22) in the water inlet quick-fit connection (23)
and screw up to the connection (20).
Operation A in fig. 2.
OPERATION - PRELIMINARY ACTIVITIES
• Move the high-pressure cleaner to work position.
• Completely unwind the high-pressure hose (14).
• Attach a supply pipe to the water inlet’s quick connection (23) using a normal garden connector.
Operation F
in fig. 6.
• Open the water supply tap and make sure this is not dripping;
- if the connection is made to the drinking water mains, a
BA
type water mains disconnector (26) must be
used, in conformity with EN 12729 standard, and available from your dealer
(fig. 5).
With regard to its use,
refer to the relative instruction manual;
- in case of supply from a water tank, introduce the suction hose inside the tank and make sure the vertical
distance between the water level and the pump is no more than 1.5 m (4.9 ft).
Operation G in fig. 5.
• Make sure the master switch (1) is on
“0”
position and insert the plug.
Operation C in fig. 6.
• Move the master switch (1) to position
“1”
.
• Press the spray gun lever (19) and wait for a continuous jet of water to come out;
• Move the master switch (1) to
“0”
position and connect the lance hose (10) to the spray gun (9), tightening
well.
operation B in fig. 6.
Summary of Contents for ETM Series
