![background image](http://html1.mh-extra.com/html/lavor/eg-m-3800/eg-m-3800_instruction-manual_3963008013.webp)
13
DE
set-up.
n
Connect the supply and drain hoses.
Mount the supply hose to connection (6)
and the drain hose to connection (4).
n
Place a suction valve with filter on the end
of the supply hose to prevent the supply
from clogging up.
n
Place a check valve directly on the drain
hose to prevent the pump from being
damaged by water hammer.
n
Place a shut-off valve downstream from
the check valve to facilitate servicing.
•
Before installing or moving the
pump always remove the mains
plug from the wall socket.
Connecting the water hose (fig. A)
n
Screw a water hose directly or via a
reducing nipple to the connection.
n
Check whether the hose is connected
properly.
•
Before connecting a water hose,
always unplug the tool.
Filling the pump housing (fig. A)
Before each use the pump housing must be
filled with water.
n
Remove the screw from the filling point
(5).
n
Fill the pump housing with water until
the level is equal to the edge of the filling
point.
n
Re-insert the screw and tighten it
securely.
Instructions for use
n
Check whether the hoses are connected
properly.
n
Make sure that the supply hose is
approximately 0.5 m below liquid level.
n
Fill the pump housing with water.
Switching on and off (fig. A)
n
To switch the machine on, set the on/off
switch (1) to ‘I’.
n
To switch the machine off, set the on/off
switch (1) to ‘0’.
•
The pump has been fitted with
a thermal protection. In case of
overload the motor is switched off.
After the motor has cooled down
the pump automatically switches
on again.
CLEANING AND MAINTENANCE
The pump is maintenance free.
n
Regularly clean the ventilation slots.
n
Defects must only be repaired by an
authorised service station.
•
The pump must not be opened by
the user.
Bleeding the pump housing (fig. A)
After each use the pump housing must be
drained.
n
Remove the water hoses present.
n
Remove the screw from the bleeding
point (7).
n
Tilt the machine forward and empty the
pump housing.
n
Re insert the screw and tighten it securely.
•
Never fully close the bleeding
point if you leave the machine in
an area colder than 0 °C.
IMPORTANT (FOR UK ONLY)
If the moulded 3 pin plug attached to this
unit is damaged and needs replacing, it
is important that it is correctly destroyed
and replaced by an approved BS 1363/5A
fused plug and that the following wiring
instructions are followed.
The wires in this mains lead are coloured in
accordance with the following code:
blue neutral
brown live
green and yellow earth
As the colours of the wires in the mains
lead of this unit may not correspond to the
coloured markings identifying the terminals
in your plug, proceed as follows:
n
The wire which is coloured blue must
Summary of Contents for EG-M 3800
