![background image](http://html1.mh-extra.com/html/lavor/8-621-1004/8-621-1004_manual_680797021.webp)
21
EN
tric cable. Have a damaged power cord
replaced immediately by an authorized
service point or an electrical specialist.
WARNING:
Appliance with fl uid under
pressure. Keep a fi rm hold on the gun and
be prepared to take the kickback pressure.
Only use the high pressure nozzle provid-
ed with the appliance.
WARNING:
The high pressure hose is de-
signed and produced to withstand high
pressures. To avoid damage, it must be
handled with special care. Misuse may
lead to premature breakages or damage
and cause the loss of warranty cover.
WARNING:
The appliance is not to be used
by children or persons with reduced physi-
cal, sensory or mental capabilities, or lack
of experience and knowledge, unless they
have been given supervision or instruc-
tion.
WARNING:
Children being supervised not
to play with the appliance.
WARNING:
Never start the high-pressure
cleaner without fi rst completely unwind-
ing the high-pressure hose.
WARNING:
When winding and unwinding
the pipe take care not to cause the high-
pressure cleaner to overturn.
WARNING:
Before unwinding or wind-
ing the hose, switch the machine off and
release the pressure in the hose itself
(switching off ).
> WATER SUPPLY
Water supply connection
Caution - Danger!
Only clean or fi ltered water should be used
for intake. The delivery of the water intake tap
should be equal to the double of the maximum
pump range.
Minimum delivery rate: 30 l/ min.
-
Maximum intake water temperature: 40°C
-
Max inlet water pressure: 1Mpa
-
Place the cleaner as close to the water supply
system as possible.
Water supply from the water main
• Connect a supply hose (not included) to
the water inlet of the unit (ref. 6, pos. 1)
and to the water supply (max. pressure 10
bar).
• Connect high pressure hose to the ma-
chine connection (ref. 6, pos. 2) and turn
on the water tap.
The cleaner can be connected directly to the
mains drinking water supply hose is fi tted with
a backfl ow preventer valve as per current regu-
lations in force.
Make sure that the hose is at least Ø 13 mm and
that it is reinforced.
Failure to comply with the above conditions
causes serious mechanical damage to the
pump and the loss of warranty cover.
> HIGH PRESSURE HOSE
WARNING:
The high pressure hose is de-
signed and produced to withstand high
pressures. To avoid damage, it must be
handled with special care.
Misuse may lead to premature breakages or
damage and cause the loss of warranty cover.
(See illustrations).
> ELECTRICITY SUPPLY
- The appliance’s electrical connection must
comply with the IEC 364 standard.
Before connecting the appliance, make
sure that the nameplate data are the same
as those of the electrical mains and that
the socket is protected by a diff erential
security breaker with tripping sensitivity
below 0.03 A - 30 ms.
- If the appliance’s plug is not compatible
with the socket, have the socket replaced
with another of suitable type by profes-
sionally qualifi ed staff .
- Never use the appliance in ambient tem-
peratures below 0° C if it is equipped with
a PVC (H VV-F) cable.
WARNING:
Inadequate extension cords
can be dangerous.
Summary of Contents for 8.621.1004
