Lauterbach C5000 Debugger Manual Download | Manualshive

Page: 55 / 72

background image

C5000 Debugger | 55

©

1989-2022

Lauterbach

SYStem.Option.OVERLAY

Enable overlay support

Default: OFF.

Example

:

SYStem.Option.PWRDWN

Allow power-down mode

Default: OFF.

If this option is OFF, the debugger forces the chip to keep clock and keep power on OMAPxxxx devices.

Format:

SYStem.Option.OVERLAY

[

ON

|

OFF

|

WithOVS

]

ON

Activates the overlay extension and extends the address scheme of the
debugger with a 16 bit virtual overlay ID. Addresses therefore have the
format

<overlay_id>

:

<address>

.

This enables the debugger to handle

overlaid program memory.

OFF

Disables support for code overlays.

WithOVS

Like option

ON

, but also enables support for software breakpoints. This

means that TRACE32 writes software breakpoint opcodes to both, the

execution area

(for active overlays) and the

storage area

. This way, it is

possible to set breakpoints into inactive overlays. Upon activation of the
overlay, the target’s runtime mechanisms copies the breakpoint opcodes to
the execution area. For using this option, the storage area must be readable
and writable for the debugger.

SYStem.Option.OVERLAY ON

Data.List 0x2:0x11c4

; Data.List <overlay_id>

:

<address>

Format:

SYStem.Option.PWRDWN

[

ON

|

OFF

]

«
...
53
54
55
56
57
...
»

Summary of Contents for C5000 Debugger









































































Reviews:

No comments

Related manuals for C5000 Debugger

AllShare Cast Dongle

Brand: Samsung Pages: 2

Brand: D-Link Pages: 14

Brand: Idis Pages: 123

Brand: Idis Pages: 29

Brand: Idis Pages: 28

DirectIP DR-1304P

Brand: Idis Pages: 82

Brand: T&D Pages: 122

Brand: Furuno Pages: 24

Brand: NEC Pages: 2

Supero SAS-826A

Brand: Supero Pages: 16

XM24 Expansion Module

Brand: Avaya Pages: 5

Vortex86SX VSX-6100

Brand: ICOP Technology Pages: 50

Brand: Renesas Pages: 4

Brand: PADAUK Pages: 27

Power System S914

Brand: IBM Pages: 48

Brand: Microcomputer Systems Pages: 21

Quark SoC X1000

Brand: Galileo Pages: 20

Brand: Cabletron Systems Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands