Lathem PC700 User Manual Download | Manualshive

Page: 9 / 52

background image

Welcome

•

5

Install the PC700 Series Clock

Step 1:

Select a site to install your clock that will be convenient to

employees clocking in and out. When deciding where the clock will
be installed, keep in mind that an 115vAC power outlet should be
within reach of the mounting location as well as a connection to the
network (LAN).

Note:

It is recommended to install and mount the clock before

installing the PayClock software. With the clock powered up and
connected to the network (LAN), the software will search for it on the
network and automatically configure the clock.

Step 2:

After selecting the appropriate installation site, use masking

tape to hold the included Mounting Template onto the wall. Drill holes
using the template as a guide. Note: the bottom of the clock should
be about

45

inches from the floor.

Remove the Template from the wall and install the included
mounting screws. Install the three larger screws, leaving
approximately 3/16 inch of the screws exposed.

Do not tighten all

the way

. Retain the smaller screw for later.

Note:

For sheetrock walls, drill a 3/16” diameter hole through each of

the four screw locations; each approx 1-1/2” deep. Install the plastic
“anchors” included in the mounting screw packet.

«
...
7
8
9
10
11
...
»

Summary of Contents for PC700





















































Reviews:

No comments

Related manuals for PC700

Brand: La Crosse Technology Pages: 11

Brand: La Crosse Technology Pages: 18

Brand: La Crosse Technology Pages: 2

Brand: La Crosse Technology Pages: 2

Brand: La Crosse Technology Pages: 6

Brand: La Crosse Technology Pages: 3

Brand: La Crosse Technology Pages: 12

Brand: La Crosse Technology Pages: 10

Brand: La Crosse Technology Pages: 4

Brand: La Crosse Technology Pages: 8

Brand: La Crosse Technology Pages: 8

Brand: Dexford Pages: 4

Brand: JBL Pages: 12

Brand: Sammut Pages: 8

Brand: Roberts Pages: 24

ECHOFLEX Wireless TimeClock

Brand: ETC Pages: 36

Brand: Casio Pages: 1

Brand: DS Produkte Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands