Lathem 7500E User Manual Download

Page: 2 / 50

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to Part 15 of FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment

is operated in a commercial environment. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and used in accordance

with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be required to correct the

interference at his or her own expense.
Caution: Changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate the

equipment.

Lathem Time Corporation

www. lathem. com

(800) 241-4990
(404) 691-1065

This User's Manual and its contents are copyrighted by LATHEM

WARNING

Summary of Contents for 7500E



















































Search results

Summary of Contents for 7500E

Reviews:

Related manuals for 7500E

Brands by name

Popular brands

Lathem 7500E, User Manual

Search results

Summary of Contents for 7500E

Reviews:

Related manuals for 7500E

Brands by name

Popular brands