background image

22

45

44

9. SPECIFICATIONS

Clock accuracy

Calendar

Printing system

Dimensions

Weight

Rating

Power failure 
compensation

Print at power 
failure

Memory capacity

Operating
environment

Monthly accuracy 

±

 15s (at ordinary temperature)

Year  up  to  2099.    Automatically  adjusted  to  leap  years,  31-day 
months and months with thirty or fewer days, and the days of the 
week.

Dot matrix 

Three  years  of  cumulative  power  failure  hours  after  the  date  of 
shipment

Special battery, 100-time printing or 24 hours (optional) 

Temperature: -5˚ to + 45˚C
                     : + 23˚ to + 113˚F
Humidity: 20 to 80%RH, no condensation
The  unit  operates  normally  at  temperatures  of  5˚C  or  below,  but 
the  print  density,  reaction  of  the  liquid  crystal  display,  and  the 
number  of  prints  at  power  failure  are  inferior  to  those  at  normal 
temperature operation.
6.3" (w) x 8.07" (h) x 5.04" (d) 
160 (w) x 205 (h )x 128 (d) mm

Approx. 3.5lbs. (1.6kg)

120VAC  50/60Hz  0.3A

100 employee capacity

Optional  battery  (not  included)  for  100%  printer  operation  during  power  failures  is 
available. Order part no. VIS6020

Place the time recorder at the position close to the wall outlet so that it is easily accessible 
to disconnect.
Lithium battery contains perchlorate material - special handling may apply.
Please  go  to  the  web  site  http://www.dtsc.ca.gov/hazardouswaste/perchlorate  for 
information about proper methods of disposal. 

Ni-MH Battery rated 8.4V, 600mAh.  Caution: Replace only with the same type of battery
specified by the manufacturer.

Summary of Contents for 7500E



















































Reviews: