background image

5. Installing and connecting the video doorphone components
Installing and connecting the MVC-7002 monitor

For easier installation, all the wires of the video doorphone can be run to a standard
cable box installed in the wall. Once mounted, the monitor should cover the whole box.
This will make it easier to install and mount the monitor.
- The monitor is mounted on a metal holding bracket fixed to the wall. To fix the bracket,
place it against the wall in the intended place of installation and mark holes for rawl
plugs.
- Drill the holes as market and fix the bracket to the wall using rawl plugs.
- Connect the wires to the J102 socket connector provided with the kit, as shown in the
diagram, by soldering them to the wiring system. Protect all soldered connections and
isolated portions of the wires against short-circuit with a shrinking sleeve or insulating
tape. Plug the connectors to the sockets.
- Mount the monitor on the holding bracket.

Installing and connecting the additional monitor

For connecting two MVC-7002 monitors to a single outdoor panel, run a separate power
supply (J100 socket) to the additional monitor and connect the two monitors. See Figure
4, 5 and 6 (p. 7, 8)

Fig 7. Connectors in MVC-7002 monitor

9

Pin to J102 socket

(

optional - connection

additional external panel

)

Pin to J103 socket

(

optional - connection

additional external panel

)

Pin to J100 socket

(power supply)

red

+

black

-

red

audio

white

wideo

yellow

Vcc+

blue

masa

red

audio

white

wideo

yellow

Vcc+

blue

masa

Installing and connecting the BVC-6504 outdoor panel.

- Unscrew the screw holding the panel to the hood.
- Place the hood at the intended place of installation, mark holes for the rawl plugs and

drill the holes (Fig. 8b, p. 10). The camera lens should be placed at a height of approx.
150 cm (see Fig 8a, p. 10).

- Pull the wiring system cable through the circular hole in the casing and fasten the

casing to the wall (Fig. 8c, p. 10).

- Connect the wires according the diagram (see Fig. 5, p. 7). As shown in Fig. 5, the

LASKOMEX PPUH, ul. D¹browskiego 249, 93-231 £ódŸ, tel. (42) 671 88 00, fax (42) 671 88 88, e-mail: [email protected], http://www.laskomex.com.pl

Summary of Contents for Bastion Apus II

















Reviews: