manualshive.com logo in svg

Laser Cut Planes HogNose, Building Instructions, Page: 19 / 30

Share
Download
Laser Cut Planes HogNose Building Instructions Download Page 19

March 19, 2018

HogNose building instructions

19

Top rear of fuselage

Remove all covering from along the 
horizontal stabiliser joint.

Remove the covering from the pushrod 
slots on both sides of the fuselage.

Step 40.

Locate "WS" (sheet 6).
Remove the covering from the 
slots just under the cockpit 
roof. Feed "WS" through the 
slots.

Ensure that "WS" is the 
correct way up. I.E. the tips 
are higher than the centre.

There are marks to position 
"WS" centrally but if these 
have been obscured by the 
painting, measure each side 
to get it exactly central.

Then turn the model over to 
gain access to the joint 
through the windscreen hole 
and run glue along the joint 
as shown.

Remove covering
from pushrod slots.
Both sides

Tenons for horizontal
stabiliser must be free
from covering

Remover covering
from these notches

Slit the covering
to allow undercarriage
to fit.

Remove the covering from the notches for 
the wing stays.

Slit the covering to allow the undercarriage 
wire to enter its slot.

Measure from fuselage
to tip of "WS" to get
both sides equal.

VERY 
IMPORTANT.
"WS" MUST 
BE CENTRAL

Glue along 
this joint

Remove covering
from slots

Positioning marks

 

Summary of Contents for HogNose































Reviews:

No comments