manualshive.com logo in svg

Laser Cut Planes HogNose, Building Instructions, Page: 16 / 30

Share
Download
Laser Cut Planes HogNose Building Instructions Download Page 16

March 19, 2018

HogNose building instructions

16

Locate the 2 items "E2" (sheet 2) 
and item "E1" (sheet 6)
Fit them together as shown on a flat 
surface, (all markings on underside). 
 Note that "E1" is slightly thinner 
than "E2".
The front edge MUST be in a straight 
line so set this against a straight 
edge and glue "E1" into place.
Ensure no glue enters the slots for 
the elevator control horn.
Set aside.

Step 33

Step 36

Locate items "SA" and "SB", 2 
of each. (sheet 6). These are 
the wings stays.

Fit each pair together as shown 
on a flat surface, Glue the 
joints.
Ensure a strong joint.

Set aside.

Locate "VS" and "R". vertical 
stabiliser (sheet 3) and rudder. 
(sheet 4)

Lightly sand and round off the 
edges shown. The joining edges 
should be left square.

Step 34

Locate "HS" (sheet 5), and the 4 
ribs marked "D" and "E". (sheet 4).

Fit he ribs into "HS" as shown and 
on a flat surface, glue into place.

Set aside.

Step 35

Round off

Round off

Square

Square

E2

E2

E1

This edge MUST be straight

No glue in slots  

Summary of Contents for HogNose































Reviews:

No comments