Lantech IES-2008 User Manual Download Page 68

Page: 68 / 71

SNMP MIB

RFC 1213 MIBII

RFC 1493 Bridge MIB

RMON RFC 1757

RFC 2674 VLAN MIB

RFC 1643 Ethernet like MIB

RFC1215 Trap MIB

IGMP MIB.

Private MIB for switch information, redundant

ring, port alarm, TFTP firmware upgrade, reset,

port mirror, IP security

SNMP Trap

Up to 3 Trap stations

Cold start, Port link Up, Port link down,

Authentication Failure

Private Trap for power status

Port Alarm configuration

Fault alarm, redundant ring

Class of service

IEEE802.1p class of service support

Per port provides 4 priority queues

Quality of service

The quality of service support port based

Tag based and IPv4 Type of service

Redundant ring

2 ports for redundant ring to provide redundant

backup feature and the recovery time below

300ms. It also supports coupling ring function.

Ring and coupling port configure by web

interface and ringmaster by hardware DIP

switch

VLAN

Port based VLAN

IEEE802.1Q Tag VLAN

Both of port based and Tag based VLAN group

up to 64 VLANs

Summary of Contents for IES-2008








































































Search results

Summary of Contents for IES-2008

Reviews:

Related manuals for IES-2008

Brands by name

Popular brands

Lantech IES-2008, User Manual

Search results

Summary of Contents for IES-2008

Reviews:

Related manuals for IES-2008

Brands by name

Popular brands