Lantech IES-2008 User Manual Download Page 11

Page: 11 / 71

DIP Switch No

Status

Description

OFF

Disable port 1 Alarm

Enable port 1 Alarm. If the port’s link

fails, the fault LED will light up.

OFF

Disable port2 Alarm

Enable port 2 Alarm. If the port’s link

fails, the fault LED will light up.

OFF

Disable port3 Alarm

Enable por3 t Alarm. If the port’s link

fails, the fault LED will light up.

OFF

Disable port4 Alarm

Enable port4 Alarm. If the port’s link

fails, the fault LED will light up.

OFF

Disable port 5 Alarm

Enable port5 Alarm. If the port’s link

fails, the fault LED will light up.

OFF

Disable port 6 Alarm

Enable port6 Alarm. If the port’s link

fails, the fault LED will light up.

OFF

Disable port 7 Alarm

Enable port 7 Alarm. If the port’s link

fails, the fault LED will light up.

Summary of Contents for IES-2008








































































Search results

Summary of Contents for IES-2008

Reviews:

Related manuals for IES-2008

Brands by name

Popular brands

Lantech IES-2008, User Manual

Search results

Summary of Contents for IES-2008

Reviews:

Related manuals for IES-2008

Brands by name

Popular brands