manualshive.com logo in svg

Lanier LD1110, Operating Instructions Manual

Share
Download
Lanier LD1110 Operating Instructions Manual Download Page 218

Appendix

198

5

• Inch  version

400% (Area ratio 16 times): -
200% (Area ratio 4 times): 5

1

/

2

" 

×

 8

1

/

2

"

→

11" 

×

 17"

155% (Area ratio 2 times): 5

1

/

2

" 

×

 8

1

/

2

"

→

8

1

/

2

" 

×

 14"

129%: 8

1

/

2

" 

×

 11"

→

11" 

×

 17"

121%: 8

1

/

2

" 

×

 14"

→

11" 

×

 17"

93%: -
85%: F

→

8

1

/

2

" 

×

 11"

78%: 8

1

/

2

" 

×

 14"

→

8

1

/

2

" 

×

 11"

73%: 11" 

×

 15"

→

8

1

/

2

" 

×

 11"

65%: 11" 

×

 17"

→

8

1

/

2

" 

×

 11"

50% (Area ratio 

1

/

4

times): 11" 

×

 17"

→

5

1

/

2

" 

×

 8

1

/

2

"

25%: -

❖

Zoom

• The reproduction ratios you can specify are 25 - 400%.
• You can select a ratio regardless of the size of an original or copy paper.

With some ratios, parts of the image might not be copied or margins will
appear on copies.

❖

Auto Reduce/Enlarge

• The reproduction ratios you can specify are 25 - 400%.

❖

Size Magnification

• The reproduction ratios you can specify are 25 - 400%.

❖

Directional Size Magnification

• The reproduction ratios you can specify are 25 - 400%.
• When entering a percentage ratio, you can specify any value in the permit-

ted range, regardless of original or copy paper size. However, depending
on settings and other conditions, part of the image may not be copied, or
margins will appear on copies.

• When entering a size in mm, if the calculated ratio is over maximum or un-

der minimum ratio, it is automatically adjusted to within available range.
However, with some ratios, parts of the image might not be copied or mar-
gins will appear on copies.

❖

Sort, Stack

• Following shows the stackable paper sizes and the orientation.

Finisher SR5000:
A3

L

, B4 JIS

L

, A4

KL

, B5 JIS

KL

, 11" 

×

 17"

L

, 8

1

/

2

" 

×

 14"

L

, 

8

1

/

2

" 

×

 11"

KL

, 5

1

/

2

" 

×

 8

1

/

2

"

KL

, 12" 

×

 18", 13" 

×

 19"

• Paper sizes and orientations that can be used in the Rotate Sort function are

A4

KL

, B5 JIS

KL

 and 8

1

/

2

" 

×

 11"

KL

.

• Following numbers of copied paper are stackable on the output tray. If the

number of copied paper exceeded the limits listed in the following table,
be sure to remove the copied paper once.

Summary of Contents for LD1110











































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands