manualshive.com logo in svg

Lanier LD1110, Operating Instructions Manual

Share
Download
Lanier LD1110 Operating Instructions Manual Download Page 2

Introduction

This manual contains detailed instructions and notes on the operation and use of this machine. For your
safety and benefit, read this manual carefully before using the machine. Keep this manual in a handy
place for quick reference.

Important

Contents of this manual are subject to change without prior notice. In no event will the company be li-
able for direct, indirect, special, incidental, or consequential damages as a result of handling or oper-
ating the machine.

Notes:

Some illustrations in this manual might be slightly different from the machine.

Certain options might not be available in some countries. For details, please contact your local dealer.

Caution:

Use of controls or adjustments or performance of procedures other than those specified in this manual
might result in hazardous radiation exposure.

Notes:

The model names of the machines do not appear in the following pages. Check the type of your ma-
chine before reading this manual. (For details, see “Machine Types”, About This Machine.)

•

Type 1: 8090/DSm790/LD190/Aficio MP 9000

•

Type 2: 8110/DSm7110/LD1110/Aficio MP 1100

•

Type 3: 8135/DSm7135/LD1135/Aficio MP 1350

Certain types might not be available in some countries. For details, please contact your local dealer.

Two kinds of size notation are employed in this manual. With this machine refer to the inch version.

For good copy quality, the supplier recommends that you use genuine toner from the supplier.

The supplier shall not be responsible for any damage or expense that might result from the use of parts
other than genuine parts from the supplier with your office products. 

Power Source

208 - 240V, 50/60Hz, 20A

Please be sure to connect the power cord to a power source as above. For details about power source,
see “Power Connection”, Troubleshooting.

Power Supply

The socket-outlet shall be installed near the product and shall be easily accessible.

Summary of Contents for LD1110











































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands