Lang LGR36-NFR Owner'S Manual Download

Page: 21 / 24

NFRARED

OMPACT

ROILER

ERVICE

WNER

’

ANUAL

1192039

(10/09)

AGE

ARTS FOR

LGR48-NFR

AND

LGR48-RAD

NITS

The following table describes the serviceable parts for LGR48-NFR and LGR48-RAD units. For parts not listed,
contact a Lang Authorized Parts Distributor or a Lang Authorized Service Agency.

PARTS LIST LGR48

Qty.

PARTS LIST LGR48

Qty.

Part Number

DESCRIPTION

NFR RAD

Part Number

DESCRIPTION

NFR RAD

1183202

BODY SIDE, LEFT

1183248

TUBE, BURNER SUPPLY ( V )

1183323

BODY SIDE, RIGHT

1183264

TUBE, PILOT ADJUST

1183273

BRACKET, BEARING LOCK

1183310

TUBE, FLEX, ¼ X 16” LG.

1183278

BRACKET, SPRING ADJUST

1183315

NIPPLE, PIPE, BLK. 3/8” X 8”

1183304

PLATE, COVER

1183259

TUBE, BURNER SUPPLY (H)

1183308

BRACKET, ARM ADJUST

1183295

SPRING, PIVOT ARM

1183269

CLIP, RETAINER

1183311

SPRING, RACK

1183332

BRACKET, ORFICE

1160484

ROLLER BEARING

1183160

FRONT, BODY, 48

1192015

HANDLE, OVEN DOOR

1183142

BASE, 48

1192008

BRACKET, HANDLE LEFT

1183144

GREASE DRAWER, BA

1192009

BRACKET,HANDLE RIGHT

1183174

GREASE DRAWER, SS

1192016

SCREW, #8x1

1183141

BODY, BOTTOM/BACK, 48

1192000

KNOB, RED METAL WITH INSERT

1183145

STIFFENER, CAVITY, AZ, 48

1192018

KNOB, RED BALL

1183161

COVER, 48

1183279

WEIGHT, CONTER BALANCE

1183159

PLATE, HEAT DEFLECTOR, 48

1183287

SPACER, BEARING

1183155

RACK, MOUNT ANGLE, 48

1164085

VALVE ASM, PILOT

1192022

PLATE, FACE, SS

1192020

NAMEPLATE, LANG

1183150

DRIP PAN, 48

1183158

TUBE, VALVE SUPP, 48

1183171

MOUNT, BURNER, 48

1183162

RACK, NFR-48 (CHROME)

1183169

DEFLECTOR, FLUE, 48

1183165

RACK, NFR-48 (CRS)

1183246

ASM, BURNER

(NAT) GAS COMPONENTS

1183251

W/A, MANIFOLD

1133301

REGULATOR, WC @ 4” NAT

1183277

W/A, BRACKET BEARING

1176014

VALVE, BURNER, NAT

1183271

W/A, BEARING PIVOT

1108754

ORIFICE HOOD, DRILL #54

1183281

W/A BRACKET, BEARING

1182628

PILOT ASSY SGS

1183293

W/A, ARM SWING

1183306

W/A, ARM, CONNECTOR

(PROP) GAS COMPONENTS

1183319

W/A, RACK ADJUST (LEFT)

1165704

REGULATOR, WC @ 10”, PROP

1183320

W/A, RACK ADJUST (RIGHT)

1176015

VALVE, BURNER, PROP

1183331

ASM, MANIFOLD BURNER

1008764

HOOD, ORIFICE, DRILL #64

1182628

PILOT ASSY SGS

1183117

W/A, RACK CRADLE-48

1183120

W/A, RACK CARRIAGE-48

1183126

ASM, INNER LINING, AZ, 48

1183127

W/A, SHAFT-48”

Summary of Contents for LGR36-NFR

























Search results

Summary of Contents for LGR36-NFR

Reviews:

Related manuals for LGR36-NFR

Brands by name

Popular brands

Lang LGR36-NFR, Owner'S Manual

Search results

Summary of Contents for LGR36-NFR

Reviews:

Related manuals for LGR36-NFR

Brands by name

Popular brands