background image

L&L VENT-SURE DOWNDRAFT KILN VENT INSTRUCTIONS

ventsure-instruct.pdf 

REV: 8/1/2017 

Page 11

©

 

2017  

 

L&L Kiln Mfg, Inc.  505 Sharptown Rd, Swedesboro NJ 08085  856.294.0077   F:856.294.0070   [email protected]   hotkilns.com   

M-V-OUTT/00 ..................................................................(see web) 

Motor Outlet Duct. This is the piece of duct that attaches to the 

outlet of the motor. 
M-V-90EL/00 ...................................................................(see web) 

90 Deg 4” elbow. Used for attaching to motor mount duct to the 

outside to prevent water from getting into duct.
M-V-CORD/00 ................................................................ (see web) 

Power Cord for Vent-Sure. Includes a cord mounted on/off switch. 

(Call factory for non-USA cords)

Power Cord with On/Off switch:

M-V-DUCT/00 ................................................................. (see web) 

Flexible Vent Duct 2-1/2 to 15 Feet Expandable, Flexible 

Aluminum 3” duct with two hose clamps.

Flexible Aluminum Duct shown with hose clamps:

M-V-BBOX/00 ................................................................ (see web) 

Bypass Collection Box. Includes hardware for mounting and slide 

control. Note: This has the proper mounting hole configuration to 

be mounted to any L&L kiln stand. It can also be mounted to the 

side of other kilns (typically on the bottom section).

Bypass Collection Box:

M-V-MULT/00 ................................................................. (see web) 

Mult-Mounting Bracket. Comes with six (6) sets of 1/4-20 bolts, 

nuts and lock washers for mounting this to the “Wall mount 

bracket” (M-V-VENT/BK).

This special “Multi-Mounting Bracket” will allow you to 

mount the vent on the floor or wall with the outlet of the vent 

pointing up. There are mounting holes on the bottom (for floor 

mounting) and on the side as well (for wall mounting):

M-V-VENT/DB ................................................................ (see web) 

Vent Doubler System for Vent-Sure. Includes a “T” duct with 

dampers, an extra Bypass Collection Box, Extra Flexible Duct.

(Consider buying the Multi-Mounting Bracket which is not included 

but sometimes useful for this installation as shown in the photo-

graph).

Vent Doubler System:

M-V-TDUC/00 ................................................................. (see web) 

“T” DUCT to attach two aluminum flexible ducts to. Includes  

dampers on the two inlets. The outlet fits onto the Motor Inlet 

Duct of the Vent-Sure and the Flexible Vent Duct(s) fit onto the 

inlets of this “T” Duct. 

Special “T” duct for doubler system:

Summary of Contents for M-V-VENT/00












Reviews: