background image

L&L VENT-SURE DOWNDRAFT KILN VENT INSTRUCTIONS

ventsure-instruct.pdf 

REV: 8/1/2017 

Page 10

©

 

2017  

 

L&L Kiln Mfg, Inc.  505 Sharptown Rd, Swedesboro NJ 08085  856.294.0077   F:856.294.0070   [email protected]   hotkilns.com   

MOTOR SPECIFICATIONS

120 VOLT MOTOR

PSC Blower, Type:Forward Curve, Direct Drive
Wheel Dia. (In.):3-15/16,Wheel Width (In.):2-1/2
CFM @ 0.000-In. SP:146, CFM @ 0.100-In. SP:140, CFM 

@ 0.200-In. SP:126, CFM @ 0.300-In. SP:124. CFM @ 

0.400-In. SP:120, CFM @ 0.500-In. SP:110,
Voltage:115, Hz:50/60, Phase:1, Full Load Amps:0.75, 

RPM:3100
Bearing Type:Ball, Motor Type:Permanent Split Capacitor, 

Motor Enclosure:Open, Motor Insulation:Class B, Thermal 

Protection:Auto
Lead Length (In.):13, Conduit Box:Yes,
Ambient Temp. (Deg. F):104, Max. Inlet Temp. (Deg. F):104
Inlet Dia. (In.):3-1/8, Outlet Height (In.):2-3/16, Outlet 

Width (In.):3-1/4, Overall Height (In.):5-3/4, Overall Width 

(In.):6-5/16, Overall Depth (In.):5-3/8, Mounting:All Position, 

Housing Finish:Gray Enamel, Housing Material:Rolled Steel
Agency Compliance:UL Recognized US and Canada 

(E47479)

220-240 VOLT MOTOR

Item-PSC Blower,Type-Forward Curve, Direct Drive
Wheel Dia. (In.):3-3/4, Wheel Width (In.):1-7/8
CFM @ 0.000-In. SP:133,CFM @ 0.100-In. SP:128, CFM 

@ 0.200-In. SP:126, CFM @ 0.300-In. SP:119, CFM @ 

0.400-In. SP:112, CFM @ 0.500-In. SP:105, 
Voltage:230, Hz:50/60, Phase:1
Full Load Amps:0.33, RPM:2880
Bearing Type:Ball, Motor Type:Permanent Split Capacitor, 

Motor Enclosure:Open, Motor Insulation:Class B, Thermal 

Protection:Auto, Lead Length (In.):13, Conduit Box:Yes, 

Ambient Temp. (Deg. F):104, Max. Inlet Temp. (Deg. F):104
Inlet Dia. (In.):3-1/4, Outlet Height (In.):2-1/2, Outlet Width 

(In.)2-9/16, Overall Height (In.)6-9/16, Overall Width (In.):5-

5/8, Overall Depth (In.):6-9/16
Mounting:All Position, Housing Finish:Gray Enamel, 

Housing Material:Rolled Steel
The Vent-Sure vent is c-MET-us listed in both the US and 

Canada for use with L&L listed kilns. UL 499, CSA C22.2, 

No. 122, CSA C22. Listing No E112742.

PARTS

Prices of all parts are listed at: 

hotkilns.com/parts
Complete Vent-Sure Kiln Vent System

M-V-VENT/00 ................................................................. (see web)
VENT-SURE Vent. 120 Volt. Complete System as described 

above and on our separate Vent-Sure brochure. This includes the 

motor, an 8 foot cord with a rocker type On/Off switch mounted 

in line in the cord, the inlet duct attached to the motor,  the wall 

mounting bracket, a 90 deg elbow for mounting on the end of the 

outlet pipe (to keep rain water out), the Bypass Collection Box 

for attaching to the kiln stand or kiln side along with mounting 

hardware for mounting to an L&L kiln stand and one section of 15 

foot flexible aluminum duct with hose clamps. 
M-V-VENT/41 ................................................................. (see web)
VENT-SURE Vent. 220-240 Volt. Typically used in non-US instal-

lations.

You can also purchase individual parts to suit your 

own configuration or as replacements:

Below shows the vent system blower assembly with the motor, 

cord and switch set, 3” inlet duct to hold the flexible duct, 12” 

duct to go through a wall and 90 Degree elbow. 

M-V-FANK/00..................................................................(see web)
Complete blower assembly. Pictured above ^
M-V-FAN0/00 ................................................................. (see web) 

Fan/Blower Motor for Vent-Sure. 120 Volts. This is just the motor 

with no attached brackets or inlets. Cord is not included.
M-V-FAN0/41 ................................................................. (see web) 

Fan/Blower Motor for Vent-Sure. 220-240 Volts. This is just the 

motor with no attached brackets or inlets. Cord is not included.
M-V-BRKT/00 ................................................................. (see web) 

Steel plate onto which the motor mounts. Includes 4” x 12” outlet 

pipe and output mounting plate.
M-V-INLT/00 ....................................................................(see web) 

Motor Inlet Duct. This is the piece of duct that attaches to the inlet 

of the motor. The expandable aluminum duct fits onto this. 

Summary of Contents for M-V-VENT/00












Reviews: