Landice M1 Service Manual Download | Manualshive

Page: 20 / 26

background image

1 800 - LANDICE | [email protected] | WWW.LANDICE.COM

Folding Strut Replacement

TOOLS NEEDED:

●

5mm Allen Head Wrench ● #2 Phillips Head Screwdriver

POWER OFF THE UNIT BEFORE STARTING. REPLACE ONE STRUT AT A TIME!

Using your Allen head wrench, remove the M5x10 Allen head shoulder screws as shown above.

Step 2

You can now remove the strut from the machine. It may be helpful to unlock opposite strut and rotate

upright assembly up and down to aid with strut replacement. The new strut is shipped slightly

compressed to aid with installation. Be careful to keep the washers in place as you replace the strut.

Correct Order = Plastic/Wavy/Plastic Washer.

«
...
18
19
20
21
22
...
»

Summary of Contents for M1



























Reviews:

No comments

Related manuals for M1

Brand: Sunny Health & Fitness Pages: 21

Brand: CYBEX Pages: 41

Brand: LifeSpan Pages: 44

Brand: Gold's Gym Pages: 28

Brand: BH FITNESS Pages: 63

Brand: BH FITNESS Pages: 68

Brand: BH FITNESS Pages: 73

Brand: BH FITNESS Pages: 71

560hr Treadmill

Brand: ProForm Pages: 34

Brand: Cory Everson Pages: 18

Brand: Dyaco Canada Pages: 30

Brand: Dyaco Canada Pages: 37

Brand: fitness gear Pages: 28

Arsalis Gaitway 3D

Brand: h/p/cosmos Pages: 108

Brand: Landice Pages: 66

360 P Treadmill

Brand: Pro-Form Pages: 23

Brand: Electronic.Star Pages: 16

Treadmill TRIAD

Brand: Ironman Fitness Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands