background image

 Landa SLT/SL

X Kubota Diesel Operator Manual  •  9.807-540.0  •  Rev. 6/13

21

 

 

PRESSURE W

ASHER

 

 

OPERA

TOR’S MANU

AL

  

PREVENTATIVE MAINTENANCE

OIL CHANGE RECORD

Check pump oil level before first use of your new Power Washer. Change pump oil after first 50 hours and  
every 3 months or 500 hours thereafter. Use SAE 10/40W non-detergent.

Date Oil Changed 

Month/Day/Year

No. of Operating Hours  

Since Last Oil Change

Brand Name and 

Type of Oil (See above)

MAINTENANCE SCHEDULE

Engine Oil
SAE 10W-30 or 
15W-40 

Inspect

Daily

Change

Every 100 hours

Filter

Every 200 hours

Air Cleaner

Inspect

Every 50 hours 

Clean

Every 3 months

Battery Level

Check monthly

Engine Fuel Filter

500 hours or 6 months

Spark Plug Maintenance

500 hours or 6 months

Clean Fuel Tank(s)

Annually

Replace Fuel Lines

Annually

Pump Oil  
(Non-detergent 
SAE 10/40W)

Inspect

Oil level daily

Change

After first 50 hours, then every 500 hours or annually

Clean Burner Filter

Monthly (More often if fuel quality is poor)

Remove Burner Soot

Annually

Burner Adjustment/Cleaning

Annually

Replace Burner Nozzle

Annually

Descale Coil

Annually (More often if required)

Replace High Pressure Nozzle

Every 6 months

Replace Quick Connects

Annually

Clean Water Screen/Filter

Weekly

Replace HP Hose

Annually

Summary of Contents for SLT6-32624E

























Reviews: