Landa SLT6-32624E, Operator'S Manual

Page: 11 / 24

Landa SLT/SL X Kubota Diesel Operator Manual • 9.807-540.0 • Rev. 6/13
11
PRESSURE W
ASHER
OPERA
TOR’S MANU
AL
SHUT DOWN AND CLEAN-UP
CAUTION: Always store your pressure washer in a
location where the temperature will not fall below
32°F (0°C). The pump in this machine is susceptible
to permanent damage if frozen. FREEZE DAMAGE
IS NOT COVERED BY WARRANTY.
1. Stop the pressure washer, squeeze spray gun
trigger to release pressure.
2. Detach water supply hose and high pressure
hose.
3. Turn on the machine for a few seconds, until re-
maining water exits. Turn engine off immediately.
4. Drain the fuel and oil from the engine.
5. Do not allow high pressure hose to become
kinked.
6. Store the machine and accessories in a room which
does not reach freezing temperatures.
CAUTION: Failure to follow the above directions will
result in damage to your pressure washer.
When the pressure washer is not being operated or is
being stored for more than one month, follow these
instructions:
1. Replenish engine oil to upper level.
2. Drain diesel from fuel tank, fuel line, fuel valve and
carburetor.
3. Pour about one teaspoon of engine oil through the
spark plug hole, pull the starter grip several times
and replace the plug. Then pull the starter grip slow-
lyuntil you feel increased pressure which indicates
the piston is on its compression stroke and leave
it in that position. This closes both the intake and
exhaust valves to prevent rusting of cylinder.
4. Cover the pressure washer and store in a clean, dry
place that is well ventilated away from open flame
or sparks.
NOTE: The use of a fuel additive, such
as STA-BIL
®
, or an equivalent, will minimize the
formulation of fuel deposits during shortage. Such
additives may be added to the gasoline in the fuel
tank of the engine, or to the gasoline in a storage
container.
After Extended Storage
CAUTION: Prior to restarting, thaw out any
possible ice from pressure washer hoses,
spray gun or wand.
Engine Maintenance
During the winter months, rare atmospheric conditions
may develop which will cause an icing condition in the
carburetor. If this develops, the engine may run rough,
lose power and may stall. This temporary condition can
be overcome by deflecting some of the hot air from the
engine over the carburetor area.
NOTE: Refer to the
engine manufacturer's manual for service and mainte-
nance of the engine.
STORAGE
STEP 2: Turn burner switch off and
continue spraying, allowing the wa-
ter to cool to below 100°. STEP 3: Turn engine key switch
off. STEP 1: Remove detergent suction
tube from container and insert into
one gallon of fresh water. Open
detergent valve, pull trigger on
spray gun and siphon water for one
minute.
98075400-21
Burner
Switch
STEP 5: Squeeze trigger on spray
gun to relieve remaining pressure. STEP 4: Turn off water supply.
Engine
Key
Switch
9.8
01-
427
.0 OF
F
GLST
DO NOT OVE
RLOA
D GENE
RAT
OR
Uni
ts e quip
ped
with o
ptio
nal gene
rator
shoul
d no
t ex
cee d 10
00
wat ts re
sistive
load.
See Se
rvic e Manual
for details
.
CA
UTIO
N
ON
TACH
/HO UR
FO
R O
UTDO
OR U
SE O NL
Y — S
TO
RE IN
DOO RS
As sem
ble
d i n U
SA
Us e A
pp rov
ed D ete
rge
nt On
ly.
Co nta
ins co
mp on
en ts
from
on e o
r m ore
of
the
fol
lowin
g co un
tries
:
Un ite
d S tat
es, C hin
a, I
tal y, J
ap an an
d T
hai lan
d.
8.9 32-9
68. 0
98075400-22
9.801-427.
0 OF
F
GLST
DO N
OT OV
ERLOAD
GENERA
TOR
Units eq
uipped with
optional
gen era
tor
should not ex
ceed 10
00 watt
s resi stiv
e
load.
Se
e Se
rvic e Manu
al fo r deta
ils.
CA
UTION
ON
TACH
/HOU
R
98075400-23
98075400-24 98075400-25