background image

4

How To Use This Manual

This manual contains the following sections:

How to Use This Manual

Safety

Operations

Maintenance

Parts List

The HOW TO USE THIS MANUAL section will tell you 
how to find important information for ordering correct 
repair parts.

Parts may be ordered from authorized dealers. When 
placing an order for parts, the machine model and 
machine serial number are important. Refer to the 
MACHINE DATA box which is filled out during the 
installation of your machine. The MACHINE DATA box 
is located on the inside of the front cover of this manual. 

The model and serial number will be found on a decal 
attached to the machine.

The SAFETY section contains important information 
regarding hazardous or unsafe practices of the 
machine. Levels of hazards are identified that could 
result in product damage, personal injury, or severe 
injury resulting in death.

The OPERATIONS section is to familiarize the operator 
with the operation and function of the machine.

The MAINTENANCE section contains preventive main-
tenance to keep the machine and its components in 
good working condition. They are listed in this general 
order:

Winterizing Procedure

High Limit Thermostat

Cleaning of Coils

Rupture Disk

Fuel

Ignition Circuit

Electrode Setting

Burner Nozzle

Fuel Control System

Air Adjustment

Coil Removal HS-3000

Maintenance

Preventative Maintenance

The PARTS LIST section contains assembled parts 
illustrations and corresponding parts list. The parts lists 
include a number of columns of information:

REF – 

column refers to the reference number 

on the parts illustration.

PART NO.

 – column lists the part number for 

the part.

QTY

 – column lists the quantity of the part used 

in that area of the machine.

DESCRIPTION 

– column is a brief description 

of the part.

NOTES 

– column for information not noted by 

the other columns.

NOTE: If a service or option kit is installed on your 
machine, be sure to keep the KIT INSTRUCTIONS 
which came with the kit. It contains replacement parts 
numbers needed for ordering future parts.

NOTE: The manual part number is located on the 
lower right corner of the front cover.

Model:

Date of Purchase:

Serial Number:

Dealer:

Address:

Phone Number:

Sales Representative:

Landa HS  Operator’s Manual  8.913-943.0 - P

Summary of Contents for 1.103-900.0
























Reviews: