background image

Important Safety Information

8/30/22

4

Handle 

Chemicals Properly

Protective clothing should be 

worn.

Handle all chemicals with care. 

Follow instructions on container 

label.

Agricultural chemicals can be 

dangerous. Improper use can 

seriously injure persons, animals, 

plants, soil, and property. 

Inhaling smoke from any type of 

chemical fire can be a serious 

health hazard.

Store or dispose of unused 

chemicals as specified by the 

chemical manufacturer.

Dig Safe - Avoid 

Underground Utilities

USA: Call 811

CAN: digsafecanada.ca 

Always contact your local utility 

companies (electrical, telephone, 

gas, water, sewer, and others) 

before digging so that they may 

mark the location of any 

underground services in the area. 

Be sure to ask how close you can 

work to the marks they positioned.

Listed below are common practices that may or may not be applicable to the products 

described in this manual.

Avoid crystalline Silica 

(quartz) Dust

Because crystalline silica is a basic 

component of sand and granite, 

many activities at construction sites 

produce dust containing crystalline 

silica. Trenching, sawing, and boring 

of material containing crystalline 

silica can produce dust containing 

crystalline silica particles. This dust 

can cause serious injury to the 

lungs (silicosis).
There are guidelines which should 

be followed if crystalline silica 

(quartz) is present in the dust.

Be aware of and follow OSHA 

(or other local, State, or Federal) 

guidelines for exposure to airborne 

crystalline silica.

Know the work operations where 

exposure to crystalline silica may 

occur.

Participate in air monitoring or 

training programs offered by the 

employer.

Be aware of and use optional 

equipment controls such as water 

sprays, local exhaust ventilation, 

and enclosed cabs with positive 

pressure air conditioning if the 

machine has such equipment. 

Otherwise respirators shall be worn.

Where respirators are required, wear 

a respirator approved for protection 

against crystalline silica containing 

dust. Do not alter respirator in any 

way. Workers who use tight-fitting 

respirators can not have beards/

mustaches which interfere with the 

respirator seal to the face.

If possible, change into disposable 

or washable work clothes at the 

work site; shower and change into 

clean clothing before leaving the 

work site.

Do not eat, drink, use tobacco 

products, or apply cosmetics in 

areas where there is dust containing 

crystalline silica. 

Store food, drink, and personal 

belongings away from the work 

area.

Wash hands and face before eating, 

drinking, smoking, or applying 

cosmetics after leaving the exposure 

area.

Summary of Contents for RTR2570







































Reviews: