Land Pride Rotary Cutter RCR2684 Operator'S Manual Download Page 3 | Manualshive

Page: 3 / 54

background image

Table of Contents

7/26/19

©

Copyright 2019 All rights Reserved

Land Pride provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the
preparation of this manual, Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use
of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this
product at the time of its publication, and may not reflect the product in the future.

Land Pride is a registered trademark.

All other brands and product names are trademarks or registered trademarks of their respective holders.

Printed in the United States of America.

RCF2784 & RCR2684 S/N Rotary Cutters 326-364M

Table of Contents

Important Safety Information . . . . . . . . . . . . . 1

Safety at All Times   . . . . . . . . . . . . . . . . . . . . . . . . . 1
Look For The Safety Alert Symbol   . . . . . . . . . . . . . 1
Safety Labels  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Using This Manual . . . . . . . . . . . . . . . . . . . . . . . . 10

Terminology: . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Definitions: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Owner Assistance . . . . . . . . . . . . . . . . . . . . . . . . . 10

Further Assistance . . . . . . . . . . . . . . . . . . . . . . . 10

Section 1: Assembly & Set-up . . . . . . . . . . . 11

Tractor Requirements  . . . . . . . . . . . . . . . . . . . . . . 11
Torque Requirements  . . . . . . . . . . . . . . . . . . . . . . 11
Uncrating Instructions  . . . . . . . . . . . . . . . . . . . . . . 11
Gearbox Vented Dipstick   . . . . . . . . . . . . . . . . . . . 11
Tractor Shutdown Procedure   . . . . . . . . . . . . . . . . 12
3-Point Hitch Set-up   . . . . . . . . . . . . . . . . . . . . . . . 12

3-Point Single Tailwheel Option . . . . . . . . . . . . . 14
3-Point Dual Tailwheel Option . . . . . . . . . . . . . . 15

Driveline Installation   . . . . . . . . . . . . . . . . . . . . . . . 16
3-Point Tractor Hook-up   . . . . . . . . . . . . . . . . . . . . 16
Driveline Hook-up  . . . . . . . . . . . . . . . . . . . . . . . . . 17

Check Driveline Collapsible Length  . . . . . . . . . . 18
Check Driveline Maximum Length  . . . . . . . . . . . 19
Check Driveline Interference  . . . . . . . . . . . . . . . 19

Pull-Type Hitch Set-up (RCF2784) . . . . . . . . . . . . 20

Hitch Assembly . . . . . . . . . . . . . . . . . . . . . . . . . 20
Driveline Installation . . . . . . . . . . . . . . . . . . . . . . 20
Axle Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Pull-Type Tractor Hook-up (RCF2784) . . . . . . . . . 23
Assembly of Optional Guards . . . . . . . . . . . . . . . . 24

Front Rubber Guard (RCF2784)   . . . . . . . . . . . . 24
Front Chain Guards  . . . . . . . . . . . . . . . . . . . . . . 24
Rear Chain Guards   . . . . . . . . . . . . . . . . . . . . . . 24
Pull-Type Hydraulic Hook-up  . . . . . . . . . . . . . . . 25
Purge Hydraulic System   . . . . . . . . . . . . . . . . . . 25

Section 2: Adjustments . . . . . . . . . . . . . . . . . 26

3-Point Leveling & Cutting Height . . . . . . . . . . . . . 26

Deck Leveling   . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Cutting Height Adjustment  . . . . . . . . . . . . . . . . . 26
Single & Dual Tailwheel Adjustment   . . . . . . . . . 27
Center 3-Point Link Adjustment  . . . . . . . . . . . . . 27

Pull-Type Leveling & Cutting Height (RCF2784) . . 28

Deck Leveling   . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Front To Back Deck Leveling  . . . . . . . . . . . . . . . 28
Cutting Height Adjustment  . . . . . . . . . . . . . . . . . 29

Section 3: Operating Instructions . . . . . . . . . 30

Operating Checklist  . . . . . . . . . . . . . . . . . . . . . . . . 30
Safety Information  . . . . . . . . . . . . . . . . . . . . . . . . . 30
Inspection of Tractor & Cutter  . . . . . . . . . . . . . . . . 31
Transporting   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Blade Engagement & Disengagement . . . . . . . . . . 32

Blade Engagement . . . . . . . . . . . . . . . . . . . . . . . 32
Blade Disengagement . . . . . . . . . . . . . . . . . . . . 32

Field Operation  . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Unhook Rotary Cutter  . . . . . . . . . . . . . . . . . . . . . . 32
General Operating Instructions  . . . . . . . . . . . . . . . 33

Section 4: Options . . . . . . . . . . . . . . . . . . . . . 34

Front and Rear Safety Guard Options . . . . . . . . . . 34

Front Rubber Guard  . . . . . . . . . . . . . . . . . . . . . . 34
Front Chain Guards  . . . . . . . . . . . . . . . . . . . . . . 34
Rear Chain Guards   . . . . . . . . . . . . . . . . . . . . . . 34

Hitch/Wheel Options . . . . . . . . . . . . . . . . . . . . . . . 35

3-Point Hitches . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Pull-Type Hitch (RCF2784) . . . . . . . . . . . . . . . . 35

Pull-Type Height Adjustment Options . . . . . . . . . . 35

Ratchet Height Adjustment . . . . . . . . . . . . . . . . . 35
Hydraulic Height Adjustment . . . . . . . . . . . . . . . 35

Section 5: Maintenance & Lubrication . . . . . 36

Maintenance  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Driveline Slip-Clutch   . . . . . . . . . . . . . . . . . . . . . . . 36
Clutch Run-In   . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Clutch Assembly and Disassembly  . . . . . . . . . . . . 37

Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Cutter Blade Maintenance  . . . . . . . . . . . . . . . . . . . 37
Skid Shoe Maintenance . . . . . . . . . . . . . . . . . . . . . 39
Long-Term Storage  . . . . . . . . . . . . . . . . . . . . . . . . 40
Ordering Replacement Parts  . . . . . . . . . . . . . . . . . 40
Lubrication Points  . . . . . . . . . . . . . . . . . . . . . . . . . 41

Gauge Wheel Spindle Tube (3-Point Cutters)   . . 41
Gauge Wheel Hub  . . . . . . . . . . . . . . . . . . . . . . . 41
Gearbox  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Driveline U-Joints  . . . . . . . . . . . . . . . . . . . . . . . . 42
Driveline Shield Bearings  . . . . . . . . . . . . . . . . . . 42
Driveline Profiles   . . . . . . . . . . . . . . . . . . . . . . . . 42
Ratchet Jack (Optional) (RCR2784)  . . . . . . . . . . 42

Section 6: Specifications & Capacities  . . . . . 43
Section 7: Features & Benefits   . . . . . . . . . . . 46
Section 8: Troubleshooting  . . . . . . . . . . . . . . 47
Section 9: Torque Values Chart . . . . . . . . . . . 48
Section 10: Warranty   . . . . . . . . . . . . . . . . . . . 49

«
1
2
3
4
5
...
»

Summary of Contents for Rotary Cutter RCR2684























































Reviews:

No comments

Related manuals for Rotary Cutter RCR2684

Brand: Tanaka Pages: 11

Brand: Horizon Fitness Pages: 412

Brand: Velleman Pages: 4

Brand: Black+Decker Pages: 27

Brand: ST. SpA Pages: 28

Brand: 2M2 Pages: 24

Brand: Haussmann Xpert Pages: 12

Brand: RASOR Pages: 16

ALLGAS Mobile Pro

Brand: Rothenberger Pages: 124

Brand: ESER Pages: 39

Brand: CAB Pages: 22

Brand: Far Tools Pages: 47

Brand: Zenoah Pages: 36

Brand: Larzep Pages: 6

Brand: Laski Pages: 40

Brand: GCC Technologies Pages: 196

Omk.SZP01.E11.0101.Z5F

Brand: omake Pages: 49

Brand: Fein Pages: 77

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands