Land Pride Rotary Cutter RCR2684 Operator'S Manual Download Page 28 | Manualshive

Page: 28 / 54

background image

Section 1: Assembly & Set-up

RCF2784 & RCR2684 S/N Rotary Cutters 326-364M

24

Table of Contents

7/26/19

Assembly of Optional Guards

DANGER

!

To avoid serious injury or death:

Rotary Cutters have the ability to discharge objects at high
speeds; therefore, the use of front and rear safety guards is
mandatory with this cutter. Stop blade rotation if a bystander
is in or around the area.

Front Rubber Guard (RCF2784)

Refer to Figure 1-17:

1.

Install Front Rubber Guards (#1 & #2) as shown with
3/8"-16 x 1" GR5 carriage bolts (#3), and hex whiz
nuts (#4).

2.

Tighten nuts to the correct torque.

Front Chain Guards

Land Pride offers a front chain guard for the RCF2784 &
RCR2684. A double chain guard is also offered for the
RCF2784. The chain guards are designed to handle
heavy applications where cutter blades make contact
with solid dense objects.

Refer to Figure 1-18:

1.

Install front chain guards (#1 & #2) as shown with
3/8"-16 x 1" GR5 carriage bolts (#3), and hex whiz
nuts (#4).

2.

Tighten nuts to the correct torque.

Rear Chain Guards

Land Pride offers a rear chain guard for the RCF2784 &
RCR2684. A double chain guard is also offered for the
RCF2784. The chain guards are designed to handle
heavy applications where cutter blades make contact
with solid dense objects.

Refer to Figure 1-19:

1.

Remove the standard rear metal band guard and
hardware.

2.

Install rear chain guard (#2) with four 1/2"-13 x 1"
GR5 carriage bolts (#3), and hex whiz nuts (#5).
Draw whiz nuts up snug, do not tighten at this time.

3.

Install 1/2"-13 x 3 1/2" GR5 carriage bolts (#4),
deflector spacers (#1), and hex whiz nuts (#5). Draw
whiz nuts up snug.

4.

Tighten all whiz nuts (#5) to the correct torque.

IMPORTANT:

The RCF2784 & RCR2684 come

standard with a rear metal band guard which must
be removed before installing an optional rear chain
guard.

Front Rubber Guard Option

(RCF2784 Only)

Figure 1-17

Front Single Chain Guard Option

RCF2784 Shown

Figure 1-18

Rear Single Chain Guard Option

RCF2784 Shown

Figure 1-19

33028

33027

33010

«
...
26
27
28
29
30
...
»

Summary of Contents for Rotary Cutter RCR2684























































Reviews:

No comments

Related manuals for Rotary Cutter RCR2684

Brand: Makita Pages: 372

Brand: Makita Pages: 19

Brand: Makita Pages: 32

Brand: Makita Pages: 28

Brand: Makita Pages: 11

Brand: Makita Pages: 24

PEGAS 121 PLASMA

Brand: Alfa IN Pages: 22

Brand: Brush Wolf Pages: 20

Brand: Textron Pages: 10

Brand: IVT Pages: 92

Brand: Ioline Pages: 8

Brand: Raider Pages: 76

Brand: Power Craft Pages: 17

Brand: Power Craft Pages: 24

Brand: ES manufacturing Pages: 5

Brand: Proxxon Pages: 54

Brand: BERGSPORT-STEINLE Pages: 2

Vario duplex 4000

Brand: Olympia Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands