Land Pride Rotary Cutter RCR2684 Operator'S Manual Download Page 20 | Manualshive

Page: 20 / 54

background image

Section 1: Assembly & Set-up

RCF2784 & RCR2684 S/N Rotary Cutters 326-364M

16

Table of Contents

7/26/19

Driveline Installation For RCR2684 & RCF2784 (RCF2784 Shown)

Figure 1-7

Driveline Installation

DANGER

!

To avoid serious injury or death:

Make certain driveline yokes are securely fastened at each
end. A loose yoke can work free allowing the driveline to
rotate uncontrollably causing implement damage and bodily
injury or death to anyone nearby.

Refer to Figure 1-7 on page 16:

1.

Remove rubber protective sleeve (#8) from gearbox
input shaft and discard.

2.

Unsnap one end of access doors (#9) and rotate
doors open.

3.

Slide slip-clutch end of driveline (#11) onto gearbox
input shaft until hole in driveline yoke aligns with
groove in gearbox shaft. Insert M12 x 1.25 x 65mm
GR8 bolt (#2) and secure with flat washer (#4) and
hex nylock nut (#3). Tighten nylock nut to the correct
torque.

4.

Push/pull on driveline yoke to be sure it is securely
fastened to the gearbox shaft.

5.

Collapse driveline (#11) by pushing on tractor end of
driveline towards the cutter gearbox shaft.

6.

Rotate driveline hanger (#13) down and support
driveline (#11) on the hanger.

7.

Rotate access doors (#9) closed and snap in place.

IMPORTANT:

The drivelines must be lubricated

before putting them into service. Refer to

“Lubrication Points”

3-Point Tractor Hook-up

Refer to Figure 1-7:

DANGER

!

To avoid serious injury or death:

•

A crushing hazard exists while hooking-up and unhooking

implement. Keep people and animals away while backing-
up to implement or pulling away from implement. Do not
operate hydraulic controls while a person or animal is
directly behind the power machine or near the implement.

•

All guards and shields must be installed and in good

working condition while operating the implement.

•

Do not engage power take-off while hooking-up or

unhooking the driveline, or while someone is standing near
the driveline. A person’s body and/or clothing can become
entangled in the driveline.Always follow “Tractor
Shutdown Procedure” provided in this manual before
dismounting the tractor.

A tractor with 3-Point Category lI or lII hitch is required.
The lower 3-Point arms must be stabilized to prevent
side-to-side movement. Most tractors have sway blocks
or adjustable chains for this purpose.

1.

Slowly back tractor to the Rotary Cutter while using
tractor’s 3-Point hydraulic control lever to align lower
3-Point arm hitch holes with clevis hitch pin holes.

IMPORTANT:

The tractor’s lower 3-point arms must

be stabilized to prevent side-to-side movement.
Most tractors have sway blocks or adjustable chains
for this purpose.

NOTE:

Land Pride’s Quick Hitch can be attached to

the tractor to provide quick and easy 3-point hook-
up and detachment. See your nearest Land Pride
dealer to purchase a Quick-Hitch.

«
...
18
19
20
21
22
...
»

Summary of Contents for Rotary Cutter RCR2684























































Reviews:

No comments

Related manuals for Rotary Cutter RCR2684

Brand: YABE Pages: 52

Brand: CHANCE Pages: 2

Brand: Textron Pages: 16

Brand: Tanaka Pages: 17

Brand: Hitachi Pages: 24

Brand: Hitachi Pages: 52

Brand: Hitachi Pages: 25

Brand: Hitachi Pages: 18

Brand: Logan Graphic Products Pages: 2

Brand: ES Pages: 2

Brand: Dahle Pages: 24

Brand: Dahle Pages: 28

Brand: Homelite Pages: 169

Brand: Signode Pages: 2

Brand: Land Pride Pages: 40

Brand: OREC America Pages: 50

Brand: Danfoss Pages: 76

Brand: Cross Tools Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands