background image

Kit Assembly Instructions

5

2/2/22

L02 Third Function Valve Kit Assembly Instructions Manual No. 380-366M   

Disassembling Tractor’s Original 

Loader Control Lever

Refer to Figure 1-8:

1. Pull control lever’s rubber boot (H) from loader valve 

cover (J) to gain access to the loader lever lock 

nut (K).

2. Loosen loader lever lock nut (K), then remove the 

original control lever (L) by unthreading it counter 

clockwise.

Disassembling Original Loader Control Lever

Figure 1-8

3. Remove control lever lock nut (K) and rubber boot (H) 

from original control lever (L) for reinstallation on the 

new third function control lever (#38).

4. Store original control lever (L) for safe keeping.

Installing Third Function Control 

Handle Assembly

Refer to Figure 1-9 through Figure 1-14 on page 6:

1. Modify the rubber boot (H) as shown in Figure 1-9 to 

allow clearance for the third function wire harness.

Control Lever Boot Modification

Figure 1-9

2. Insert threaded side of third function control handle 

lever (#38) and its corresponding wire harness 

through the rubber boot (H) as shown in Figure 1-10.

3. Hand thread original control lever lock nut (K) to the 

base of the threads on the third function control 

handle lever (#38).

K

J

H

L

76119

Cut boot for wire harness 

clearance.

H

72561

Preparing Third Function Control Handle Assembly

Figure 1-10

4. Fold wire harness towards the control handle, then 

thread control handle lever (#38) into the control 

lever mounting block (M) until lock nut (K) is almost in 

contact with mounting block (M). Refer to Figure 1-11.

Installing Third Function Control Handle Assembly

Figure 1-11

5. Orient control handle assembly (#36) so both red 

button switches (#42) are facing the tractor’s left side.

Orienting Third Function Control Handle Assembly

Figure 1-12

H

38

K

76120

Third function 

wire harness

36

Third function 

wire harness

M

38

K

76121

76122

36

42

Summary of Contents for L02



















Reviews: