Land Pride CB0550, Operator'S Manual

Page: 14 / 28

Section 1: Assembly & Set-up
2/5/19 CB0550 4-in-1 Combination Bucket 381-139M
10
Table of Contents
Hook-up With BX Quick Hitch
DANGER
!
To avoid serious injury or death:
A crushing hazard exists while hooking-up and unhooking the
attachment. Do not allow anyone to stand between attachment
and power machine while approaching or backing away from
the attachment. Do not operate lift and/or tilt controls while
someone is near the power machine and/or attachment.
WARNING
!
To avoid serious injury or death:
Make sure bucket is properly attached to Kubota’s quick hitch
to keep it from coming loose and falling. The bucket’s center
hitch pin must be cradled in the quick hitch j-hook and clevises
must be pinned to the quick hitch with hitch pins. Hitch pins
must be secured with retaining pins.
Follow instructions below if hooking bucket to “Kubota
Original Quick Hitch” Option No. BX6315. If hooking
bucket directly to the front loader, skip to “Hook-up
Without BX Quick Hitch” on page 11.
Refer to Figure 1-6:
1. Check for and remove any debris in the hitch point
areas before hooking up the 4-in-1 Combination
Bucket.
2. Remove retaining pins (#3A) and hitch pins (#3B).
3. Rotate top of quick hitch forward and lower loader
arms until j-hook (#5) is positioned at a height to fit
under center hitch pin (#2).
4. Slowly drive tractor forward until j-hook (#5) is
positioned under center hitch pin (#2).
5. Slowly raise loader arms and rotate top of quick hitch
back until center hitch pin (#2) is fully seated in
j-hook (#5) and holes in bushings (#4) are in-line with
clevis pin holes (#1).
6. Shut tractor down properly. Refer to “Tractor
Shutdown Procedure” on page 7.
7. Insert hitch pins (#3B) in clevises (#1) and lower
quick hitch bushings (#4).
8. Secure hitch pins (#3B) with wire retaining
pins (#3A) as shown in Detail A.
9. Refer to Figure 1-9 on page 12: Connect hose
couplers (#6 & #7) to bulk head couplers "A" & "B".
See
“Hydraulic Hose Hook-up” on page 12 for
detailed instructions.
Unhook With BX Quick Hitch
WARNING
!
Store attachment in a secure position on solid, level ground
with upper jaw fully closed. If stored improperly, the
attachment can easily tip over onto a person.
Refer to Figure 1-6:
1. See “Long-Term Storage” on page 18 when parking
bucket for long periods or at the end of the season.
2. Shut tractor down properly. Refer to “Tractor
Shutdown Procedure” on page 7.
3. Refer to Figure 1-9 on page 12: Disconnect bucket
hydraulic hoses (#6 & #7) from bulk head couplings
“A” & “B” and remove hoses from hose holder (#3). Store
hoses on bucket.
4. Remove retaining pins (#3A) and hitch pins (#3B)
from lower clevises (#1).
5. Return to the tractor, start engine, and slowly lower
loader arms while rotating top of quick hitch forward
until j-hook (#5) is below center hitch pin (#2).
6. Slowly and carefully back away from the attachment.
7. Rotate top of quick hitch back until vertical and
position loader arms to a suitable traveling height.
8. Shut tractor down properly before dismounting.
9. Replace hitch pins (#3B) in quick hitch bushings (#4)
and secure with retaining pins (#3A).
Hook-up With Kubota’s Original Quick Hitch
Figure 1-6
Detail A
3B
3A
39628
Kubota’s Original Quick
Hitch Option No. BX6315
See Detail A