LaMotte COD3 Plus Operator'S Manual Download Page 17 | Manualshive

Page: 17 / 119

background image

COD3 Plus Colorimeter 10.18

17

COMPUTER CONNECTION



OUTPUT

USB



COMPUTER CONNECTION

USB Type A, USB mini B, Order Cable Code 1720.



WATERLINK CONNECT 2

The meter may be interfaced with any Windows-based 64 bit computer by using
the LaMotte WaterLink Connect 2 program and a USB cable. The program will store
test information and results in a local database, and allow for exporting this data to
a comma separated value (CSV) ﬁ le. The meter will send the following data: time/
date stamp, name of test, sample value, sample units, meter name, and location.
To download WaterLink 2 go to http://www.waterlinkconnect.com/ . Then select
“Products” > “WaterLink Connect 2 Application” > “Download”.

BATTERY



BATTERY/AC OPERATION

The colorimeter may be operated on battery power, using a USB wall adapter or USB
computer connection. If using the meter as a bench top unit, use the wall adapter if
possible to extend the battery life. The meter will remain on when the USB adapter is
used.

To charge the battery with the wall adapter, plug the smaller end of the USB cable
(USB mini B connector) into the meter and the larger end of the USB cable (USB Type
A connector) into the wall adapter. Plug the wall adapter into an AC outlet. Reinsert the
USB port plug after charging.

To charge the battery from a computer, plug the smaller end of the USB cable (USB
mini B connector) into the meter and the larger end of the USB cable (USB Type A
connector) into a USB port on a computer.

The battery icon will show no bars and ﬂ ash when the unit ﬁ rst turns on. Then the
indicator will indicate the battery status by showing 0, 1, 2, 3 or 4 bars.

It will take 5 hours to fully charge a low battery. The battery icon will ﬂ ash when the
battery is charging. The battery icon will show four bars and stop ﬂ ashing when it is
fully charged. The charging circuit will automatically switch to a ﬂ oat charge when the
battery is fully charged. The charger may remain connected. Some computers will NOT
supply power to their USB ports during standby operation. The wall adapter will charge
the unit continuously.

The battery icon will show no bars and continuously ﬂ ash if the battery is getting low
but the unit will still operate normally. A “Low Battery” message on the status bar of

«
...
15
16
17
18
19
...
»

Summary of Contents for COD3 Plus
























































































































Reviews:

No comments

Related manuals for COD3 Plus

DigitalFlow XMT868i

Brand: Panametrics Pages: 74

Brand: Bacharach Pages: 19

Brand: RayTek Pages: 72

Brand: Magnetrol Pages: 40

Brand: Burkert Pages: 192

Brand: QEED Pages: 6

Brand: Dwyer Instruments Pages: 189

Brand: Lowrey Pages: 109

Brand: Flowmetrics Pages: 102

WALLACE & TIERNAN P7 ADVANCED

Brand: Evoqua Pages: 98

Brand: ELGO Electronic Pages: 24

OPERA CONTROL CENTER SERVER - V 3.5

Brand: OPTICOM Pages: 21

Brand: RIDGID Pages: 18

Brand: Aethra Pages: 2

Brand: Flymaster Pages: 7

Brand: Fluidwell Pages: 48

DigiFlow 6710M-22

Brand: Savant Pages: 3

Brand: Hanna Instruments Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands