LaMotte COD3 Plus Operator'S Manual Download Page 116 | Manualshive

Page: 116 / 119

background image

APPLICATION:

Drinking and surface waters, domestic and industrial waste
water.

RANGE:

0.00–3.00 ppm Zinc

MDL:

0.05 ppm

METHOD:

Zinc forms a blue colored complex with Zincon in a solution
buﬀ ered at pH 9.0. Other heavy metals are complexed by
cyanide and the zinc cyanide complex is released by the
addition of formaldehyde before the other metal cyanide
complexes are destroyed. Sodium ascorbate is added to
reduce the interference of manganese.

SAMPLE HANDLING &
PRESERVATION:

Sample should be analyzed within 6 hours after collection.
The addition of hydrochloric acid will help preserve the
metal ion content, however the acid should be neutralized
before analysis.

INTERFERENCES:

The following ions interfere in concentrations greater than
those listed.

Ion

mg/L

Ion

mg/L

Cd(II)

1

Cr(III)

10

Al (III)

5

Ni(II)

20

Mn (II)

5

Co (II)

30

Fe (III)

7

CrO4(II)

50

Fe (II)

9

Testing

Zinc

COD3 Plus Colorimeter 10.16

«
...
114
115
116
117
118
...
»

Summary of Contents for COD3 Plus
























































































































Reviews:

No comments

Related manuals for COD3 Plus

Brand: ECC X-RAY Pages: 14

Brand: GE Pages: 8

Moisture Image 1 Series

Brand: GE Pages: 110

DigitalFlow GS868

Brand: GE Pages: 74

DigitalFlow GS868

Brand: GE Pages: 81

Brand: Baker Hughes Pages: 59

Brand: Baker Hughes Pages: 2

Brand: Panametrics Pages: 67

Brand: Panametrics Pages: 108

Transport PT878

Brand: GE Pages: 97

Brand: Bacharach Pages: 60

Brand: Bacharach Pages: 4

Brand: Bacharach Pages: 17

System SourceMeter 2601B

Brand: Keithley Pages: 13

Brand: Keller-druck Pages: 8

Brand: Omicron Lab Pages: 33

Brand: Omicron Lab Pages: 21

Brand: Omicron Lab Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands