background image

55

CORRECTING ROOM TEMPERATURE MEASUREMENT

This allows the user to correct the room temperature detected by the control unit and adapt it to different

user needs.

The entire correction procedure must be done with the control unit powered and connected to the boiler.

Room temperature correction:

Press key 

R

 and keep it pressed:

Press the  

  key.

Release key 

R

 and wait until the display shows the confirmation message “

Son

The next two stages must be done within 5 seconds otherwise the procedure will be aborted.

Release the  

  key.

Press the 

+

 key to introduce a positive correction (an increase of one unit means an increase of 0.1

°

C).

Press the 

-

 key to introduce a negative correction (a decrease of one unit means a decrease of 0.1

°

C).

Wait 5 seconds after the last modification to exit this function and recommence normal operation.

TEMPERATURE CONTROL: SELCTING THE FUNCTION MODE.

These procedures allow the user to select one of the three possible temperature control modes.

The entire procedure must be done with the control unit powered and connected to the boiler.

Choosing a temperature control function mode:

Press key 

R

 and keep it pressed:

Press the     key.

Release key 

R

 and wait for the display to show the present temperature regulator mode (

tdi

ton

 or 

trc

).

The next two stages must be done within 5 seconds otherwise the procedure will be aborted.

Release the     key.

Press the  

  key to disable the temperature regulator, press  

  to select 

ON 

-

 OFF

 regulator mode

or press   

  to select modulating regulator mode.

The display will then show the 

tdi

ton

 or 

trc

 confirmation message.

Wait 5 seconds after the last modification to exit this function and recommence normal operation.

82

PROGRAMACIÓN DE LAS TEMPERATURAS

El termostato programador permite programar 5 temperaturas fundamentales para disponer del máximo

confort deseado y del máximo rendimiento de la instalación.

TEMPERATURA DEL AGUA CALIENTE SANITARIA

La  programación  de  esta  temperatura  se  realiza  con  la  función  “circ.  sanitario”  o  “circ.  sanitario/

calefacción” activada.

Para programar esta temperatura presione el botón  

; en la pantalla aparecerá la temperatura

actualmente programada.

Manteniendo presionado el botón   

, presione los botones 

+

 y 

-

 para programar la temperatura

deseada.

Además  del  valor  visualizado,  el  símbolo   

    mostrará  gráficamente  el  nivel  de  temperatura

programado.

Soltando el botón  

  la programación será memorizada.

TEMPERATURA DEL AGUA DE CALEFACCIÓN

La programación de esta temperatura se realiza con la función “calefacción” o “circ. sanitario/calefacción”

activada.

Para  programarla  presione  el  botón     

;  en  la  pantalla  aparecerá  la  temperatura  actualmente

programada.

Manteniendo presionado el botón  

, presione los botones 

+

 y 

-

 para programar la temperatura

deseada.

Además  del  valor  visualizado,  el  símbolo   

    mostrará  gráficamente  el  nivel  de  temperatura

programado.

Soltando el botón  

  la programación será memorizada.

Si  la  caldera  está  equipada  con  sonda  exterior,  los  valores  visualizados  y  programados  serán  los

correspondientes a los valores de la temperatura externa/temperatura agua de calefacción.

TEMPERATURA AMBIENTE ESTÁNDAR

La programación de esta temperatura se realiza con la función “calefacción” o “circ. sanitario/calefacción”

programada y con la modalidad “manual”.

Presione los botones 

+

 y 

-

 para programar la temperatura deseada; en la pantalla aparecerá la tempera-

tura actualmente programada.

Tras 5 segundos desde el final de la programación, los datos serán memorizados automáticamente y la

pantalla volverá a visualizar la hora actual.

TEMPERATURA AMBIENTE CONFORT

La programación de esta temperatura se realiza con la función “calefacción” o “circ. sanitario/calefacción”

activada.

Summary of Contents for thin 24 MCS W TOP U/IT
















































Reviews: