LAMBORGHINI R7.190 DCR, Workshop Manual

Page: 4 / 41

IV
ConTEnTs
20.1.4 - Serdia 2000 20-15
20.2 - Diagnostic tool screens 20-19
20.2.1 - ECU interrogation 20-19
20.3 - Commissioning and calibrating the tractor 20-22
20.3.1 - Tractor commissioning - table of contents 20-22
20.3.2 - Scope of the document 20-22
20.3.3 - Instruments and information required 20-22
20.3.4 - Putting the transmission ECU into service - Introduction 20-22
20.3.5 - Putting the transmission ECU into service - EEPROM reset 20-23
20.3.6 - Putting the transmission ECU into service - Calibration of the clutch pedal 20-25
20.3.7 - Putting the transmission ECU into service - Calibration of the tilt sensor 20-27
20.3.8 - Putting the transmission ECU into service - Calibration of the range sensor 20-29
20.3.9 - Putting the transmission ECU into service - Automatic calibration of the gearbox clutches 20-30
20.3.10 - Putting the transmission ECU into service - Automatic calibration of the shuttle clutches 20-32
20.3.11 - Putting the transmission ECU into service - Manual calibration of the shuttle clutches 20-35
20.3.12 - Transmission ECU commissioning - Manual calibration of the shuttle clutches 20-37
20.3.13 - Putting the armrest ECU into service - EEPROM reset 20-37
20.3.14 - Putting the armrest ECU into service - Configurations 20-38
20.3.15 - Putting the services ECU into service - EEPROM reset 20-40
20.3.16 - Putting the services ECU into service - Lift calibration 20-41
20.3.17 - Putting the services ECU into service - Calibration of the ASM (SBA) system 20-43
20.3.18 - Putting the services ECU into service - Configuration of the front/rear PTO 20-43
20.3.19 - Commissioning service ECU - Front Suspension Configuration 20-43
20.3.20 - Putting the services ECU into service - Configuration of the electro-hydraulic control
valves 20-44
20.3.21 - Putting the EPB control unit into service - Initialisation 20-46
20.3.22 - Workshop Procedure for EPB Calibration 20-46
20.4 - ECU alarms 20-59
20.4.1 - Key to the “ECU alarms” tables 20-59
20.4.2 - FMI code 20-59
20.4.3 - Engine alarms 20-60
20.4.4 - Transmission alarms 20-76
20.4.5 - HLHP alarms 20-78
20.4.6 - EPB Alarms 20-80
30 - mEThoD of InTErvEnTIon
30.1 - Commercially available tools 30-2
30.1.1 - Orders 30-2
30.1.2 - 8002 - Pressing pump 30-2
30.1.3 - 8005 - Compression value tester 30-2
30.1.4 - 8011 - Pliers for hose clips 30-3
30.1.5 - 8024 - Assembly pliers 30-3
30.1.6 - 8035 - box spanner insert 30-3
30.1.7 - 8113 - box spanner insert 30-4
30.1.8 - 8114 - box spanner insert 30-4
30.1.9 - 8115 - V-belt tension tester 30-4
30.1.10 - 8189 - Torx tool set 30-5
30.1.11 - 8190 - Rotation angle gauge 30-5
Find manuals at https://best-manuals.com